Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hello,
My nRF9160 hard faults (i think?) when issuing a command to the modem, specifically this line:
which then calls ncs function:
This leads to I think is...
Hello, I'm trying to run the OpenThread CLI example on the nrf52840 chip of my NRF9160_DK. I've managed to flash the code on the nrf52 and able to see the Zephyr kernel boot...
I have tried various methods from different doccumentations and I couldn't do so. Can you provides some steps to create a west workspace.
Thanks in advance.
In my project, I am planning to use LTE modem and an external flash memory with a file system. I have problems to run code for the non-secure build type. A similar problem...
I've been tinkering for several says to get GNSS working on a Thingy91 with Zephyr.
I've tried the 'location' example and have struggled to register the device on nRFcloud...
Following the instructions to build the sample resulted in an error message ..
Here are the details ... probably something simple but not obvious to me ...
PS C:\ncs>...
Hello Everyone,
I was use Nordic App for Mesh in android to add Telink's chipset into mesh. But after few minutes, telink's device go out Mesh.
I don't know how to add...
Hi,
Iam using "pca10056_s140_ble" secure bootloader example for my project.
FYI. My project gets its new firmware from internet and stores it in BANK1 memory using GSM...
hi Support team,
customer get samples with 9160, but find out they are not able get pin code.
i searched the spec, and at command +CPIN, it is not able to read out the...
Hi,
I've installed ncs manually following this guide: Installing manually — nRF Connect SDK 2.0.99 documentation (nordicsemi.com) and then set the following environment...
Hi,
I have an application using MCUboot (Only for using with serial recovery. No SMP server running in app).
I enable CONFIG_BOOTLOADER_MCUBOOT and parent and child images...
Hi,
I am using nRF5340 DK + NCS v2.0.0 with nrfx backend for SPIM.
For my application I want to trigger a SPIM1 transaction at a fixed interval. To do this, I set up an...
Hello,
I have an issue when trying to use NVS backend for BLE settings with the settings_storage partition in defined external flash region. As we are doing a multi-image...
I am designing a bluetooth module using the soft device S130 + nRF51822. I intend to refer to QDID80592 and 45222 when purchasing DID for bluetooth. When I checked the ICS...
Hi. I am trying to develop a project that use mqtt connection using nrf9160. Currently using thingy:91 for evalutation board. I am using Mobily Network on NB IoT at Saudi...
