Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
On lesson https://academy.nordicsemi.com/courses/bluetooth-low-energy-fundamentals/lessons/lesson-4-bluetooth-le-data-exchange/topic/blefund-lesson-4-exercise-3/ , When trying...
Hi.
I'm developing a BLE peripheral application running on nRF54L15. nRF Connect SDK v3.2.1 with SoftDevice Controller is used for my application. As the title says, following...
Dear Nordic team,
We are using the nRF54L15 QFN52 package on our custom device and are using the P0.06 and P0.00 for the TX and RX, respectively, for our UART service interface...
Hi, I noticed that when using nrf5340 and it's kernel timer driver, that the k_cycle_get_64() API is not available, and that TIMER_HAS_64BIT_CYCLE_COUNTER is not being set...
Hi,
I’m planning to use a chip antenna that meets the attached specifications. I’m not very familiar with RF hardware, and I’ve only just started using CAD. I placed it...
I have a nrf52833 small board. nrf52833 QFN
and the several board have the same finding: at first time, the board can be flash and be debugged to main entrance.
but ,...
Hello this is my first time making rf circuit and i would like to get feedback on this circuit with nrf54l15.
I used Texas_SWRA117D 2.4GHz IFA antenna.
Calculated...
my nrf52833 board cannot work after power. but can start when I run nrfjprog --reset . but when I power down and power on the nrf52833 board, it do not work. the following...
When building the blinky sample with CONFIG_CLOCK_CONTROL_NRF=y set in prj.conf, the build doesn't enable the clock control and gives this warning:
Steps to reproduce...
I’d like to ask: I created a BLE keyboard based on nRF5 SDK + 52833 + S140, and it can pair and bond with Windows successfully. I have two questions:
If the keyboard...
Hi,
I am running(build and flashed successfully) the Channel Sounding example(connected_cs) from the Nordic sample and currently I want to see the distance estimation logs...
Device: nRF54L15 x 2, face to face
SDK: v3.2.2
Toolchain v 3.2.2 c717907b94
Sample code (with default setting):
channel_sounding_ras_reflector
channel_sounding_ras_initiator...
Hi, I am currently testing the channel sounding capabilities of nRF54L15 with zephyr on NCS 3.2.3. I used the sample code from nrf\samples\bluetooth\channel_sounding_ras_initiator...
Hi folks,
I'm using v3.2.2 of the nRF Connect SDK Toolchain, debugging an nRF54LM20-DK board in VS Code.
I've noticed that the "Thread Viewer" under the NRF Debug view...
