Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hi,
example : nRF5_SDK_15.0.0_a53641a\examples\peripheral\twi_sensor
I am using the HTU21D sensor. I was download the twi_scanner example to scan the HTU21D sensor's slave...
I am having a problem talking to a MMA8653FC 3-axis Accelerometer from NXP.
I never see the clock signal generated.
I am using the nRF52 lib, communicating to a nRF5280...
I am converting the the Project ‘usbd_ble_uart_pca10056_s140’ to pca10059, to download it in the nrf52840 dongle. I followed the steps in the nRF52840 Dongle Programming Tutorial...
Hi,
I have some problems when I tried to compile pc-ble-drivers (C) .
1. When I tried to execute ./bootstrap-vcpkg.bat after I follow the steps:
$ git clone github.com...
I’m studying the NRF9160-DK board - I installed the Basis SIM card and followed the instructions : www.nordicsemi.com/.../GetStarted
I launched the Link Monitor program...
Hello,
My thingy:91 is publishing its messages to nrfcloud (=to the corresponding AWS mqttEndPoint and topics/ I suppose AWS IoT Core).
Now I want to get/process these...
In the example / serial in SES I see the softdevice is loaded as an "additional load file"
$(SDK_ROOT:../../../nRF5_SDK_16.0.0_98a08e2)/components/softdevice/s140/hex/s140_nrf52_7...
I am quite new to the nrf9160. Trying to run the gps example https://github.com/ExploratoryEngineering/nrf9160-gps . But everytime I get an error Failed to start GPS. I am...
Hello, the SDK example ble_peripheral\ble_app_uart includes the code below in order to forward data from the UART over the BLE. What it does is wait for a CRLF, or a certain...
hello
i have created 1 custom service for that created 3 characteristics.
with that 3 characteristics i'm trying to notify by using nrf connect app.
my question is...
We are looking for a BLE-enabled chip which can bind to a smartphone, with the aim of performing proximity tests. to make sure the person in possession of the chip is indeed...
We want to design a small tracker for key rings like car keys etc, it will be linked with mobile app. Is it possible to do so?
Whatever I have read till now is it is possible...
Hi,
We are planning to run the nRF52840 in CKAA configuration 3 (attached) in Normal Mode. When we boot, our regulator will provide VDD = VDDH = 1.8V. Reading through the...
Our product is using NRF24L01+ and PA to transmitter data. It pass all the test of FCC PART C but the BAND Edge measurement.
The below 2 pictures is NRF24L01+ Band edge...
