Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi everyone,
I'm trying to use nRF52810 with SoftDevice S112 to sample five ADC channels. I'm finding this very weird issue, where first channel is showing correct value...
Just getting started with Nordic toolchain and I got this error below.
=== updating civetweb (modules\lib\civetweb): --- civetweb: cloning and initializing Initialized...
i need a code for when button press after one second delay led will glow continiously whenever again pressing the switch it will stop glowing using apptimer
Hi, Everyone
My development environment is sdk15.3, nRF52840, Keil complier
The link error file is attached below.
Also I am going to use AES-CBC method.
Which example...
I'm experimenting with the USB MSC example (SDK 15.3) on my nRF52840 DK. It seems to work well in the polling mode as delivered. However, when I try to run in interrupt mode...
I have a serial port set upp with the serial port library like this:
#define UART_PIN_DISCONNECTED 0xFFFFFFFF /**< Value indicating that no pin is connected to this UART...
Hello,
I am trying to get started with the 9160-DK. So far it does not seem similar to the 52840 so I decided to take to the "Getting Started Assistant" within nRF Connect...
Hi, I'm using nrf52832 and SDK15.3. And I'm using the ble_app_uart example. The device will go to sleep mode if there is no connection for 3 mins.
My questions are:
1...
I'm calling sd_ble_gap_adv_start after a connection disconnects to start advertising again and it's returning err_code 12... which is NRF_ERROR_DATA_SIZE. However, the documentation...
Hello,
I am currently working on a project that involves the host device to send configurations parameters over to the device. I was hoping the connection between in device...
Hello All,
We working on OTA features with nRF52810 using sdk16.0 . When we are trying to upload the firmware zip format through mobile its giving error "upload failed:Insufficient...
Hi,
I am new at mesh .I use SDK UART coexistence example to test, and I can scan Ble uart demo by nrf Connect APP. But I can't scan Mesh node by nrf Mesh APP. I've been...
I am trying to program the Nordic nRF51822 MDBT40 Series module to communicate to an STM32 processor chip. The way I understand the procedure is as follows:
First, I must...
