Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hi,I have some problems when disable peer manage in ble_app_buttonless_dfu project in sdk15.3.0 on nrf52810.
I disable PEER_MANAGER_ENABLED in config.h and remove the peer...
I want to save encryption state in DFU to the nrf_dfu_settings_t structure. I put a new 16-byte field at the end of the structure after nrf_dfu_adv_name_t adv_name; and whenever...
Hi,
I am specifically looking for RSSI implementation using the BLE module on nrf52840 SOC. How to obtain the RSSI values for asset tracker application on Nordic Thingy...
I'm designing a board using nRF9160 with eSIM. But according to the eSIM specifications (chip spec), the current consumption is <[email protected]. Is this continuous current consumption...
hi,
i am working on multilink. currently i connecting to 8 boards.
// <o> NRF_SDH_BLE_PERIPHERAL_LINK_COUNT - Maximum number of peripheral links. #ifndef NRF_SDH_BLE_PERIPHERAL_LINK_COUNT...
Hello,
I am using dynastream module with nrf52832. I programmed the ant module with s332 hex file and the example of ant_io_tx of s212 arm5_no_pack as below,
Im...
Hi Dears,
I have submit a issue for about two weeks but no response yet, would you please help me for handling it?
The link is https://devzone.nordicsemi.com/f/nordic...
Hello,
I am working on nRF51822, SDK12.3.0 in IAR workbench.
I am use init pin 2 as an interrupt.
Device will advertise for 20 minute after 20 minute device go to sleep...
Platform info: SDK153, MESH 3.2 and using SEGGER RTT for debug logging output with __LOG(...)
I have a strange behaviour in one of my application, where it work very fine...
Hi,
I am using nrf52 Bluetooth to transfer the data .Here i am not getting how to transfer the data at 10ms through Bluetooth.
Is there any example program to transfer...
Hi,
I'm evaluating a custom PCB that uses the MDBT50Q (nRF52840) and I'm really stuck. It looks like the device is working, but I'm getting a few strange issues.
Out of...
Dear,
we are developing a beacon product with nRF52832 powered from Li-SOCL2 primary battery. I understood that We cannot connect directly battery to the nRF52832 beacause...
Hi,
Anybody managed to connect a WisNode RAK811 to an nRF52840-DK and make them "talk" ? (send "at" commands to the RAK811 shield and get replies)
How did you connect...
Hello Nordic Community,
I am using latest firmware mfw_v1.0.1 latest NCS tag (v1.0.0) as well. I flashed GPS example into DK successfully. I made custom hardware using nRF9160...
