Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
When using the PB-ADV bearer there is a ~10 second delay after the Link is closed and the mesh stack starts working again.
This is related to my previous report https:/...
I am trying to develop a SPI interface to a CANBUS controller for the nRF9160 for the zephyr platform.
The issue I am having at this point is is that I am unable to see...
Hello,
I am working on a custom pcb with nrf9160-SICA. I have UART SPI and GPIOs running fine but I am having a very difficult time with I2c (TWI).
Pins 8 and 9 are occupied...
Hello,
I'm trying to use the nrf52840 Dongle on the Raspberry 3B+. I didn't achieve to run an appImage downloaded from your site. When i'm executing the app nothing happens...
My current hardware is based on SoftDevice SD132, v6.0.0 as provided with SDK 15.0.0. I would like to update it to use SoftDevice 6.1.0 (as part of SDK 15.2.0) and perhaps...
Hi all,
I use nRF52832-QFAA, S132 2.0.0, SDK 11.0.0, IAR 7.5 under Windows
Upon connection, I am trying to resolve the peer "random private resolvable" address (not for...
we have designed a board using Nrf9160 IC and we have issue with SIM module. we not getting 1.8 volt in "SIM_1V8" pin. when running mqtt sample program we are getting
...
Hi,
Using nRF52840 with SDK15.0.0.
I started my projetc based on BLE tutorial characteristics.
I created my service and add 2 characteristics successfully.
My module...
Hi All,
Sanity check here. I'm reading the RSSI value from a received packet
if (nrf_esb_read_rx_payload(&rx_payload) == NRF_SUCCESS) { if (rx_payload.length > 0) {...
A device that is provisioned with PB-GATT enabled stops receiving mesh packets after the provision is complete.
When the provisioning process is complete nrf_mesh_disable...
HI,
I got the following log while advertising:
SOFTDEVICE ASSERTION FAILED AT 0x00014AA6
Since this address locates at softdevice, I can not know what happens.
Would...
Hello,
Using nRF52 DK boards, I'm trying the simple_message_model by modifying the light switch example.
With the client, I simple send a 12 bytes unreliable message by...
Hello! I have a question about nordic thingy 52. Is there any possibility to play more than 8kHz on this board? For example: if i will change speaker on another it could help...
Hello, How do I set the analog reference voltage to external pin P0.02? I'm using the arduino environment so I don't know how to set it via those registers? I'm currently...
Hi,
I am using SDK 15.0 on a custom board using nRF52840. Softdevice is 6.0.0. Coding with SES.
I am investigating and trying to fix the infamous IOS caching of characteristics...
