Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hello,
In past I worked with BLE 4.0 and I remember that using the notify we have a max amount of data of 20 bytes.
Now we are working with BLE 4.2, does we have this...
The nRF Mesh Connect software available from this blog post is probably corrupted. I am not able to use it. Is there a repository for software tools where I could download...
Hi,
I am using sdk 12 with s132 v3 on nrf52832 dev board. I am running the example code for ble hid peripheral for keyboard compiled using gcc and eclipse. The example code...
Hi,Sir:
I am developing a 52840’s project using SDK15.1,My development environment is Segger embedded (version 3.34a).When I added the RNG function to the code (the correct...
Hi,
Have an issue with a prototype 2 layer 52840 pcb that i tried to get manufactured. i increased the pad diameter to 0.3mm and now i cannot route without hitting clearance...
Hi
when trying https://github.com/NordicSemiconductor/IOS-nRF-Mesh-Library everything goes OK (I think...) all the nodes gets provisioned, all the elements gets addresses...
I know the PDK design is available for download, but there are a lot of things on that board which would not be required for a minimal e.g. beacon design
I'm looking for...
We are looking at developing a proprietary protocol using the nRF52832/40 and were interested in the specific and practical differences between the Ble_2Mbit vs Nrf_2Mbit...
We try to implement DFU over UART. The Mesh DFU example has been taken as a reference. DFU is successful, but it takes about 1 hour (sic!) to transfer DFU ZIP package of size...
Hi,
We are developing a device which should have a power save mode where no BLE connection is possible (switch off the BLE to a minimum power consumption) and restart the...
Hi, there~~ Just noticed that there are codes for the Android nRF connect.
github.com/.../Android-nRF-Connect
Using that code, I wish to create my personal sniffer that...
Good afternoon,
I'm using nRF52840 with SDK15 and Softdevice6.0.0.
I'm using the Queued Write Service Module to make use of a characteristic able to receive up to 510bytes...
Please suggest a tool that can be used for monitoring and and analysis of Nordic's BLE packet transmission rate.
I would like to measure packet irregularities over time...
HI,
How to use sd_ble_opt_set() with the option BLE_GAP_OPT_SCAN_REQ_REPORT ? After setting this I can expect to get the event "BLE_GAP_EVT_SCAN_REQ_REPORT" with information...
