hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi,
How can we receive more than 20 bytes of data from the phone? We are using s132 and SDK 12.3. I know how to send more than 20 bytes of data from the NRF52 to the phone...
I am a newbie to Nordic chips and tools and new to bluetooth. My company is doing a BLE sensor. We have a prototype board ready and I am trying to do some firmware for it...
Hi I have tried the light demo example, where I do not understand the difference between "reply_Status" and "publish_State" on the server, then someone can explain the difference...
I am currently working with an NRF51822 and managed to change the TWI frequency to 400kHz in the twi_hw_master (this worked, I can see it on the oscilloscope). I commented...
I'm trying to upload via DFU from one nRF52832 to another nRF52832
I use SDK 14.1
First I want to enable CCCD at the master side.
static uint32_t cccd_configure(uint16_t...
Dear Sirs,
We are evaluating nRF52840 now, How far is the maximum range it can reach while keeping the data rate at 2Mbps if we use two nRF52840 for point-to-point communication...
i've been trying to generate hex files using keil uv5 from the examples given in the nrf52 sdk, the pregenerated hex files work as expected, wheras the ones generated by keil...
Dear Nordic Team,
Thanks for supporting.
I want to know How to add Manufacturing data with whitelist advertising . Already i am implemented without whitlist advertising...
Hello Team,
I have developed a sample Android application to use and control Nordic Thingy 52. I am able to control LED (Constant, Blink, Intensity). But I am not getting...
I want to test the mesh network for that i have to set the radio range of node to minimum distance so that i'll able to test the relay node example. Will you please help me...
Hello I am trying to make an electron application which is based from the 'pc-ble-driver-js' module for testing pupose for production development with nordic product
I am...
Hi all,
I using NRF52 kit and NUS service . When I add bond on NUS service , I still using nomal and I do not see the difference before and after I add bond . So , I want...
Hi. I am going down a rabbit hole. Wish to work with the SDK for Mesh using ideally the PCA10040 (nRF52832) and PCA10056 (nRF52840) kits.
1) Is this possible to mix the...
