Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Hello sir,
I have completed PCB design of custom nRF52832 board. Can i use following component instead of recommended part No in reference design. I have also mentioned...
Hello ,
I would like to design a custom board with nrf52832 IC and CP2102 for communication with PC serially. Unfortunately nrf52832 doesnot have Rx/Tx pins for interfacing...
Hi community,
for our application (nrf52832 / SDK 12.2) we need to store data received via BLE. The received data is a 25 kB binary blob which by design will be chopped...
Hi,
i am checking NRF52840 for USB behaviour.
I'm using example usbd_cdc_acm.
But USB receiving stucks after few bytes (between 0 and 50) and does not receives nothing...
i have nrf52 dk i run simple examle saadc from sdk 12.1.
now i want to get result.
i can't understand the code.
i start putty terminal adc event number and app info number...
I'm having trouble adjusting ram start setting using the new SES projects from latest SDK14.1.0
I have tried the project linker section placement macros settings of
...
Hello, is it possible to use a wire antenna with nRF52832?
I have read that only PCB or chip antennas are used, so I expect the answer to be no, just wanted to confirm...
Hi Nordic Engineers!
I read the description of new SD s140 v6 and find a lot of good features.
A question 1, is this the next version that will be supported in the future...
HI，all
In normal circumstances, ios phone paired and connected to my 52832 device, when they are disconnected, ios phone can automatically reconnect the ble device. But sometimes...
Hello ,
I want to use the Button with Height level to trigger.The default is Down level to trigger.What should i do for that ? I try to set BUTTON_PULL NRF_GPIO_PIN_PULLDOWN...
Hi,
I have just added over the mesh bootloader updates for my mesh and I am curious about the MBR parameter page. I want to use that page as a swap page in my application...
I set the NRF_LOG_BACKEND_RTT_ENABLED 1 and NRF_LOG_ENABLED 1 in the bootloader and application.
After a reset, the application gets stuck in the bootloader
Or maybe (bl...
