Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Okay so the issue is a little more complicated than this.
Phones used for testing were htc m8 (android 6.0) and lg g5 (android 7.0).
Ble chip running on a linux OS using...
Hello, I'm using this code(observer):
github.com/.../nRF51-multi-role-conn-observer-advertiser
SDK9.0.0
I try to add DFU function, now can enter dfu mode and iPhone6...
Hi Nordic Team,
Can you please share any information regarding Indoor Location Tracking feature/application that nRF52840 can support? does this have AoA/AoD? and can this...
I want to establish BLE connection and have a central device receive data from a peripheral device. I am using the Heart Rate Collector as an example and notice the main file...
Dear All :
Is it possible to creat a pwm with 1sec period?
Since the lowest frequency of the base clock is 125kHz，the top count of the pwm with 1sec period will be 125000...
Hi.
I havent found answer for - in my opinion - common question - how to temporarily change name of ble device on button press. As long as button isnt pressed - advertise...
Hi, I'd like to know if there is a way to subtract two different square waves that are coming from two different input pins and then measure the pulse width (or the frequency...
I have been using Power Profiler Kit nRF6707 for awhile without problem. If I made a mistake by downloading firmware when the PPK is attached to nRF52 DK, the software on...
I followed this tutorial in Infocenter and installed everything infocenter.nordicsemi.com/index.jsp , but I have a problem with Thread examples, programming output looks normally...
Hello,
I am working on nrf52840 EVB , i programmed the board BLE_APP_UART but this profile is not working , still the board functioning previously programmed blinky example...
I'm not sure exactly how to word that,
I am about to try and get the adafruit feather to consume less power in standby and I've been told the arduino library isn't well...
Hello,
I am using pca10028 and sdk 12. I want to use 2 uart for my application but as per datasheet nrf51 has only one hardware uart. Can I implement soft uart on pca10028...
Hi, I would like to measure the electricity consumed at my home(220-240V) with the nrf 51822 and send it over bluetooth. No problem on the bluetooth side, but how can I measure...
I have a buttonless device using a DFU bootloader and ble_dfu buttonless DFU service with SDK v13.0.0. I'd like to make the ble_dfu service available for 5 minutes on power...
Hi Sir,
I am using nordic nRF51822 IC for Tracking Application for that Which antenna is best ?
I have seen two type of antenna .
zig zag pcb antenna
straight...
