Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
I'm able to successfully use peripheral/uart example to read the data from GPS module. I achieved the same by setting baud rate to 4800, and connecting rx and tx of GPS to...
Hi,
Question about FOTA (firmaware upgrade over the air).
I know that nrf52832 has 512 kB of flash, and the ble stack( softdevice ) has 136 kB , and the bootloader has...
Hi,
I put my NRF52 to sleep (POWER OFF mode) and configure it to wake on GPIO port event like so:
This GPIO is set up on a reed switch. Occasionally, the NRF52 will...
Hi
I found a strange issue on nrf52832. And I use nRF5-SDK-v13.1.0 .
When I assignment P0.7->SCL & P0.6->SDA, the twi function not working. But I change the assignment...
Today I read about the new nrf52810 and I want to know about its main differences with the nrf52832.
I see a lower power consumption for the 52810 vs 52832 and no NFC on...
Hi
Currently I try to migrate my software project (with SDK14.2, S132 (5.0.0), arm-gcc toolchain ) from nRF52832 to nRF52810 (with SDK14.2, S112 (5.1.0), arm-gcc toolchain...
Hello everyone, I am a beginner in the use of Nordic Thingy: 52. I would like some help trying to reprogram the Nordic Thingy module. After a programming error of the Thingy...
HI,
I am unable to communicate between a SDK 8.0 based nRF51822 sender and SDK 14 based NRF52832 receiver.
The data rate of the SDK 8.0 sender is 250 KBits/sec, whereas...
Hi,
Can someone help me with question on SPI?
What is the difference between SPIM and SPI? They seem to have different clocks
Also in the SPIM section, the frequency...
hi,
I need to know how to use "power on reset". From the reference document, I can understand BOR and POFWARN. But the POWER ON RESET, I could not get any idea.
1. POR...
i have project with nRf51822 and uart. i use uart fifo in Uart_app_ble example sdk11. now i need disable or enable Rx, TX.i tried this function :
NRF_UART0->TASKS_STARTRX...
Hi,
Has anyone successfully used semaphores/mutex implementations of FreeRTOS?
The code I am working on is based on the FreeRTOS HRS SDK example. I am looking to add a...
Trying to compile using the on-line Mbed compiler. I keep getting cannot find "nrf.perhiperals.h", and I cannot locate it either.
Possible someone can point me in the right...
Hello.
I'm using Tielen Marjle STM32 library for nrf24l01+ ( https://stm32f4-discovery.net/2014/06/library-17-nrf24l01-stm32f4xx/ ) which worked great till now, when I...
