I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi!
I have two PCA10040 boards and I'm running the MQTT publisher example in both using a Raspberry Pi 3 Model B as a gateway.
Therefore, both boards are establishing...
Hello,
I am using pca10028 and sdk 12.2. I am trying to run some code. I am getting some make file error as ble_nus_error.PNG .
My main.c file is New Text Document (3...
Hi,
I have 2 nRF512840 eval kits and tried out the att_mtu_throughput example provided on SDK 13.0.
The throughput about 900-1000Kbps can be achieved with PHY 2.0 DLE...
Is there any way that I can use more than 4 timer in nRF 51 ??
(four or more...)
I'm using Softdevice 130, so It uses Timer 0,
and I'm using RGB Sensor using PWM Library...
i m new in NRF52832, i use saadc exemple pca 10040 sdk 13.0.0, i dont now how to get adc result from the buffer because there is 2 elements in the buffer :
err_code = nrf_drv_saadc_buffer_convert...
Hi, Nordic Forum!
We've been trying to implement an adapted version of the Secure Bootloader with Buttonless DFU in our custom board. We have successfully accomplished...
In this app by Nordic
github.com/.../Bluefruit_LE_Connect_Android
a cyclic redundancy check (CRC) is added to the payload byte array before writing it to the UART receiving...
i am creating a user interface using the sh1106 driver for a 128x64 pixel oled screen. so every screen is a list of items to be scrolled; however almost every screen i am...
Hello,
i'm currently researching the possibility of building scatternets with BLE. As the S130 softdevice supports multiple concurrent roles, it seems very possible (see...
Hi,
I'm using s140_nrf52840_5.0.0-2 and there are two characteristic for the peripheral, notification and indication. When I use notification to send data, I will get the...
Hello,
Are there examples of AES CCM encryption/decription?
Is there a recommended procedure for generating nounces?
Are there recommended procedures for using CCM...
Hi,
I have camera interfaced on GPIOs of nRF52832.. I am reading image data at the rate 80KHz.
Is it possible to write the data to SPI Flash (Slave) by DMA or by any other...
Hello,
I am using pca10028 and sdk 12.2. I am trying to add app_uart_fifo.c file to my code.
I have added the paths and also I have made changes in sdk_config.h. The changes...
