When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hello,
I found this on the forum:
According to nRF51822 PS v3.1 section 8.23 pullup and pulldown resistors have a typical value of 13kohm. if you have e.g. a button...
Hi
I got a new chip, marked as "QFAABA / 1542AB".
I see that both errata versions 1.1 & 1.2 seem to be relevant.
Can you tell me which errata should I refer to?
Thanks...
Hi Nordic,
I am adding pstorage capability to ble_app_proximity example. Before adding pstorage, the example could receive Immediate Alert from a central and set on/off to...
Hi i'm a newbie in nordic chip. Can someone please explain to me that how to enable and configure the timer interrupt and what kind of setup need to be done?
Example in...
There is a mistake in LEDS_INV_MASK definition:
PCA20006.h / nRF examples 10.0.0
#define LEDS_INV_MASK 0x11111111
// blue will be erratic
PCA20006.h / nRF examples...
Hi,
when i setting up a new project in uVision, i get a crazy Error wich i cant handle with.
My error is --> main.c: error: C3906U: Malformed via file '.\main.__i'....
Hello,
in the new version of sdk (11.0.0) you support s130 only.
That means the code contains both peripheral and central implementation.
Does it mean that s130 consume...
The following seems to suggest each write event can only contain 1 byte of data at a time.
/**@brief Event structure for @ref BLE_GATTS_EVT_WRITE. */
typedef struct...
Been playing with NRF24L01+ for a while and mostly they work as I expect. Now, I'm trying to use an ACK payload, but whenever I try to set up the receiver to put a payload...
Hi, I'm using trying to use the DFU via BLE, dual bank example from SDK 8.1.1 (with SD 8.0.0) and got it all working up to the point where I call "activate image and reset...
Hi,
I have a problem that the ANCS keeps resetting my board, so I was able to reproduce the problem on the PCA 10028 dev board.
Conditions:
iOS 8.x or 9.x
No...
Hello,
I am running Windows 10, nRFgo Studio 1.21.1 and Keil uvision 5.16a.
I was doing some tests with my nRF51 DK board, like loading the beacon example found in the...
Hello,
I am using simple_adc__pca10028 from 8.0.0 SDK to read values from my sensor, its a kind of tensometer. My configurations are:
NRF_ADC_CONFIG_RES_10BIT...
