I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
I have an application that tries to configure pin 9 of port 0 on the nrf52840. this pin is reserved for NFC use. in one application it was enough to add:
& uicr {
nfct...
Hi ,
In NCS 2.8.0 the ESB-PTX sample how to config to achieve?
Now I had disable the UART log,after transmit 20 seconds I want to config the nRF54L15 into a low power...
There are 2 software: 1.0.1 and 1.0.2. When I load the 1.0.1 hex with bootloader with the programmer, it draws 9uA current. But when I update it to 1.0.2 with DFU, the current...
We are flashing the nRF52832 that works with DFU with a SoftDevice and a bootloader. The application code is compiled privately with a private key and packaged into a zip...
Hello Nordic Team,
We have a customer who needs to use the Nordic Distance Toolbox (NDT) functionality, and they are hoping to demonstrate it on the nRF54L15 DK. Is there...
Hello, I've tried to implement rtt logging in my own project but the control block cannot be found. So I tried the saadc example and that did not work either, I tried to use...
How do I use hardware crypto on a nRF9160dk? I am using the nRF connect SDK and my build is nrf9160dk_nrf9160_ns.
Would that be cryptocell or something else? If it's cryptocell...
I am using nRF52833 / NCS 2.8.0. I'm using Gazell Pairing, but I only need pairing, not encryption. So I'm only using unencrypted pipes. If it is a non-encrypted pipe, it...
Hi,
In my design, I have a push-button that pulls low when pressed and remains floating otherwise. This button is used to wake the nRF52832 from system off mode.
The push...
Hello nordic:
May I ask about the requirement of 32M OSC of 52832 ?
EX:
Frequency tolerance
Equivalent resistance
Loading capacitance
shunt capacitance
Drive...
Hello Nordic team,
I am working on MCU nRF5340 and NCS v2.6.0 for BLE secure pairing level 4 with adding LTK (Long Term Key) share support. But, I am unable to find the...
Hi, I am currently designing the schematic for nRF24L01+ module interface with arduino nano atmega 328p MCU. Due to inventory restrictions and the current soldering capacity...
I have the SH6MDBT50Q BLE module, and I need the nRF SDK to implement a Bluetooth Mesh connection for transmitting and receiving data on both sides. I am using Segger Embedded...
