I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hi All,
Im very new to this how firmware space and would love some help.
Currently i have a NRF52840 DK Board with a Seeed Canbus shield. ( CAN-BUS Shield V2.0 | Seeed...
1. Hi i am using nrf52840 sdk ver 17.1.0 in secure bootloader /pca10056_uart_debug
2. I have flashed the dfu uart code without any change
3. while performing dfu via uart...
We are developing a ZigBee-based end device using the nRF52840. We have implemented most of the functionalities and also reporting and are able to receive reporting information...
I am working on a wearable which has Fanstel BT40F MCU (SOC nrf 5340). when i initially turn on my pmic, it can only generate 1.8 volt from buck 1 regulator and I am thinking...
Hello!
I have a custom board with an nRF52805 on it and I am simply trying to run the Zephyr blinky example and verify I can see a GPIO toggling as my first step. I installed...
Hello, I'm currently looking for a comprehensive example of DFU-OTA (Device Firmware Update Over-the-Air) using the latest SDK version with the nRF5340 platform. If anyone...
Hello im using Dwm1001C with NRF SDK 14.2 for uwb localization measurements. I have a example project that measures the position of the tag. Inside this project at some places...
I am developing application using nRF Connect SDK (v2.5.2) on custom design based on nRF52840. The design is a prototype device and currently have dozens of them assembled...
Hello!
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0, window11 pro]
I am integrating NUS central...
Dear Nordic Team,
I have a question regarding the integration of Google Find My Device into the Nordic SDK.
Our company is already registered with Google for a Find...
Hello everyone,
I’m currently exploring the Nordic Asset Tracker V2 as a foundation for my project. During my investigation, I noticed that the solution exclusively uses...
Hello all, I'm using the adafruit itsy bitsy for this modbus project and having issue to communicate with my usb-rs485 using modbus poll software. The protocol is Modbus RTU...
Hi, we're having some problems and need help. We have a usage scenario: in HOST mode, the switching rate is 250k/2M every 10ms, the time slots of the two rates are different...
Dear Team, I'm facing the issue of insufficient stack or stack overflow when I enabled configCHECK_FOR_STACK_OVERFLOW and configUSE_MALLOC_FAILED_HOOK. If i am not enable...
