Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I'm using nRF Connect version 2.9.1 with the buildprog script method of building this project.
I've got some custom boards based on the nRF5340_audio_dk. We swapped...
Hello,
I'm looking for guidance and understanding of how to properly use the KMU and ITS for secure key storage of a key generated on device.
I see that typical ITS use...
I am trying both v3.0.0 and v3.0.2 SDK; the board I am using is the nRF9160DK, version 1.1.0. There are 4 scenarios:
1) Run on Linux (minicom or Serial Terminal) following...
Hi,
I have been playing around with the configs but I could not get Mode-3 to activate. What should I change for cs configs and the prj.conf file in order to activate it...
Hi,
NCS3.0.2 on nRF52840 platform.
Using mcuboot + app build using sysbuild
in the app: shell + console are configured over cdc_acm_uart1 (connecting to e.g. COM11...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hello everyone, I'm working on Nrf COnnect SDK with nrf52832DK. I also have a Power Profiler Kit that I use for different things. I'm on Windows 11 Home version 24H2 OS build...
I have a project am I working on which is 3 HID devices and 1 CDC device. That is working just fine. It is a composite device so everything has its own interface(3 for HID...
Hello Nordic Team,
I am currently working with the NRF54L15-DK. I have successfully configured the simple ADC on AIN4 (P1.11) and am able to read the raw sensor values....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
My AD data is defined with macros as such:
I need to change the manufacturer data then update the advertising data using
My question is: How do I get a pointer to...
Currently the Matter code generation process is a bit confusing to me. Part of the code needs to be generated before building, using west zap-generate. Another part of the...
We have a product that needs to support two different customers with two different SIM. One of the SIM requires the following four extra lines in the prj.conf in order to...
Hello,
We are using the nRF9151-DK board and have soldered a new eSIM chip onto it. However, the eSIM is not being detected by the Cellular Monitor, even though we have...
Hello,
We are currently using the nrf52840 for development using Zephyr v3.7.99-ncs1 .
We want to use the UART in low power mode and therefore, we have used the zephyr...
