Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello, I'm having trouble to make the image transfer demo work.
I flashed the .hex files found here: https://github.com/NordicPlayground/nrf52-ble-image-transfer-demo to...
Hi all,
I am adding PWM to light switch server . I added success. PWM function run OK. I use PWM1,PWM2 with Timer 1 and Timer 3 and PWM library example .If I call function...
Dear Support Team,
I’m using nrf52832 and SDK 14.2.0. In my project ,there are two dsp,one is nrf52832 and the other is ntk658, they connect via uart with each other. ntk658...
Hi,
I am developing nRF52832 peripheral, SDK15.
Let me know about whitelisting.
I'd like to below functions.
1. Delete item(device) in white list.
2. Changeing...
Configuration is all 12 combinations of the following 3 x channels, 2 x modulations, and 2 x bit rates were tested to find the worst case. More substantial testing was to...
when i upload the hex file of a s132 softdevice example program through nRFgo studio,
its shows hex file uploading failed and shows this message "Invalid SoftDevice, data...
Hello Everyone,
I am facing an issue when trying to connect back BLE central again after disconnecting it from the BLE peripheral once.
The issue is reproducible as follows...
If I want to send two byte, how can I do? I use the https://github.com/NordicSemiconductor/Android-nRF-Blinky sample code.
In BlinkyManage.jave
public void send(final...
hi All!
I'm trying to use new SD140-6 function sd_ble_gap_adv_set_configure() , according to spec. if last PARAM is NULL, function behavior : " When this function is used...
Hello, there was a strange problem in the mass production of my product. The previous batch of problems was less, about 0.5%. The later batch is quite serious, 45 of 500 products...
Hej,
on trying to update firmware on nrf52832 over the air I'm getting the error message INSUFFICIENT_RESOURCES.
Actually I don't understand the error message because...
I want to put the BLE program to the firmware of another STM chip and load the program via the I2C to the nrf52832. Will it work? If yes, is there any tutorial or example...
Hello,
I'm using nRF5 SDK with version 15 and nRF52832 IC. I want to sample some data with 3200Hz sampling rate. I can set the timer minimum 1ms Which means 1000Hz. How...
