why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hello,
[Device: nRF18522 S110 Softdevice 8.0.0 SDK10]
I've referred to this post:
devzone.nordicsemi.com/.../
Does it mean the maximum value is 512 seconds...
hi,For the bluetooth certification, but requires a fixed frequency is 2402 2442 2480 test, could you tell me need how to set up 2442 under the fixed frequency?
I'm trying to make one of the examples in the SDK v9, but I'm stuck on the following error;
L:\NR - nRF firmware\Nordic SDK\V9\examples\ble_peripheral\ble_app_template...
Hi,
I use s110_6.0.0 and sdk_5.2.1 in my old product. I found that I can't write flash sometimes. Timer1 and Timer2 are used, and their interrupt priority level is 1(high_priority...
Hello,
I noticed that their was a question in the developer zone regarding MD bit?
devzone.nordicsemi.com/.../
My question is slightly different. I am using Soft...
Is it possible to use random 128-bit UUIDs for custom services and characteristics? Or do the characteristics in a service need to share 96-bits with the custom service UUID...
The hardware bug #39 on the GPIOTE in EVENT mode which gives a overconsumption of ~1mA even in idle mode on, kills the interest of having a low power chip, because the solution...
I am wondering, for 51422 or 51822, are all radios can work simultaneously or only one type of radio can work at a particular time?
e.g., BLE & ANT can work at the same...
Hi all,
Is it possible to get a callback from the softdevice, when a characteristic is changed? If so can you guide me in the right direction - documentation / examples...
@brief Function for application main entry.
*/
int main(void)
{
// Configure LED-pins as outputs.
LEDS_CONFIGURE(LEDS_MASK);
// Toggle LEDs.
while (true)
{
for...
Hi,
I'm using gazell library with app_pwm.
From documentation gazell use Timer2 and PPI channels 0,1,2.
APP_PWM use Timer0.
When I disable pwm using app_pwm_disable...
Hi,
I'm trying to use the nRF52832DK to flash a Rigado BMD-300 module (nRF52) - I've connected SWDIO, SWCLK, GND and voltage sense to P20.
It seems that because the...
I run the boardcast tx application on a nRF52832 board and I add uart drive into the proj. I use UART to console on PC.But uart doesn't work, PC console nothing. What's wrong...
I'm using the mouse example which use bonding and white list which allow to connect only to one central after performing the bonding
my question is, does the bonding feature...
Hello,
Is this the correct setup? What else will I need to do to make it work (e.g. it says something about the MCU will detect the external board and then programm/debug...
