Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hi I am not sure on the nRF51422 chip the iBeacon function is fully supported, is it ?
I can make the examples working on it but on the Nordic site only on the nRF51822 chip...
Hello,
we are trying to avoid using code that triggers hardware issue #39 in the nrf51822, which appears to be fixed in chips whose build code is Hx0.
We would like...
Hi,
I'm currently developing a firmware running on nRF51-dongles (PCA10028). The dongle communicates with a PC application over UART. Everything is working fine except...
Hello we would like to use the Nordic chip to send wireless messages from a node to other nodes directly,without hubs. We wouldn't like to be limited to up to 8 nodes receiving...
Hello,
Setup: Android 4.4.2 (LG G2), nRF51822 peripherial.
I noticed that once in a while when trying to connect to my nRF51 based device it won't connect and what is...
softdevice 8.01,app is hts. ceilphone is HTC one. nrf tools.
add some functions display，adc, eg. use nrf tools HTM connect to the board, it's reboot every time when clip...
I'm using nrf51422, SoftDevice 310 and SDK 6.1.0, when i call sd_ppi_channel_enable_set, it causes SOFTDEVICE_NOT_ENABLED error, but softdevice was enabled earlier with SOFTDEVICE_HANDLER_INIT...
Dear all.
I have some test result on DFU feature. Please any comment on this issue.
test condition
Mater control panel (64-bit version)
nRFgo studio...
In my application, I had these lines.
nrf_gpiote_event_config(0, mPinDat, NRF_GPIOTE_POLARITY_LOTOHI);
nrf_gpiote_event_config(1, mPinDat, NRF_GPIOTE_POLARITY_HITOLO...
Hi,
On iOS, is there any way to download files right into the nRF Toolbox "User files" ?
This would be useful for DFU tests, to retrieve my binaries from the web.
For...
Hi everyone,
When I set the radio's transmit power, I can use "sd_ble_gap_tx_power_set" function. If I want to get the radio's transmit power, is there any function I can...
I am using NRF_GPIOTE->EVENTS_IN[0] and NRF_GPIOTE->EVENTS_IN[1] in my software. I had my own GPIOTE_IRQHandler working.
Today I am adding UART module into my source code...
