Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hello,
I'm testing periodic advertising sample (sample/bluetooth/periodic_adv,with no changes to the code) on nRF Connect SDK 1.7.0, on BBC MICORBIT V2 that has a nRF52833...
Hi,
nRF Connect SDK 1.7.1, windows 10 X64
run SEGGER Embedded Studio.cmd or click segger_embedded_studio IDE menu File->Open nRF Connect SDK Project,
it will be got...
I have impulses coming to a GPIO input. Each pulse (say: rising edge) should toggle some other's GPIO output. What I know, is that I cat apply a task to a GPIO output. This...
I am using nrf52832 board sdk vr 17 s132 soft device. I want to have a way by which i can reduce the brightness of led while it blinks during advertising mode using PWM. pls...
Setup mcuboot and dfu to upgrade firmware on the nRF52840 of our board. Upgrading to new firmware works as expected and the new firmware is running after the install. If I...
Hi，
I am using nrf52832+freertos to develop a low-power product based on the example(ble_app_hrs_freertos) in the SDK, but now I find that the power consumption far exceeds...
Hello Nordic! I have connected a sensor to the DK via SPI. It outputs a lot of data, a lot... for 1 second of data I get 4096 entries. Each entry is 10 bytes in length.
...
I'm working on a design featuring two different MCUs. I'm looking to use the nRF52840 as one of them. I need both processors to be able to send each other messages and ideally...
Hi,
I have a weird problem. My application starts two timers, one after another. Like this:
Normally it just works - no errors, nothing. However, after a DFU OTA upgrade...
What is the best method to store TLS certificates on the nRF5340? I have seen 2 options, but I'm not sure what is best practice and what does work.
If I store the certificate...
Hi,
i just got my hands on Thingy 52, just want to know how do i get started in retrieving data from it, specifically for motion(accelerometer data), if someone can point...
Hi,
I'm trying to interface LR1110 (Dev Board) with NRF9160 DK using SPI. I have been working on this for a couple of weeks, explored almost the whole devzone, learned a...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
HI,
I need to check the following thing with you. I need to use an I2S mic with NRF5340 between the mic and the controller we need to place 2meters of wire. So, I need...
