Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
I am developing a solution with the nrf9160 that should use LTE and GPS at the same time. But unfortunately I am having some problems. Perhaps somebody from Nordic or the...
Hi everyone,
I am working on a project using nRF905 as an emitter and another Receiver(different than nRF905), the receiver is programmed in a way to perform some actions...
Hello Nordic Team,
I am having issues with the peripheral_uart firmware for the nRF52833.
1.I can use UART_init() or nrf_drv_uart_uninit() in nRF52-SDK to enable or...
hi all, 1. may i know how to get started of designing an AOA, mainly on how to send a CTE packet from TX to RX is there any code base or command that i can use? 2. i had noticed...
I am trying to establish a tunnel from ZigBee client to ZigBee server on nRF52840 using "nRF5 SDK for Thread and Zigbee v4.1.0".
Starting with the examples "examples\zigbee...
Hi everyone!
Challenge :
I'm trying to stream data from 9 nrf52832 (12 bytes each) to a computer, hopefully at 25 Hz at least (it seems more than realistic!).
Dream...
Hi !
I want to send simple HCI commands, such as reset, to the nRF5340 via UART. Therefore, I'm using the sample "hci_uart" available with nRF Connect SDK v1.5.0. I am sniffing...
It would be great to get some reassurance on this design. Is it ok for production i.e. is robust and within limits?
I am successfully driving an smd rgb led by sinking 2ma...
I am using the https fota, aws sample OK.
testd the aws certificate via Linux PC this way:
openssl s_client -connect kamacodeetrog.s3.us-east-2.amazonaws.com:443
now...
I'm trying to write the stripped down version of UART driver myself and having a few issues:
I enabled the UART, along with other registers as shown below
but when I...
on Ubuntu 20.04.2 LTS i have setup nRF connect SDK. When i try to configure segger Embedded studio. I am getting the error "create nordic project.py failed". I have connected...
The temperature sensor that i am using is analog. As mentioned above I have already gotten the temperature value using sd_temp_get().I also wish to send the values of voltage...
Hello all,
We are using Segger Embedded Studio (SES) v5.20 ,SDK v17.0.2 ,NRF52840DK board
The issue we are facing is we have a .msbl (kind of binary file)( file size 180KB...
Hi all
I want to trigger a limit event on a signal, which I receive on AIN0. Since the signal does not always have the same baseline, I set the limits with the first measurement...
This has been happening for a very long time when building nRF connect SDK applications on a windows 10 machine via the command line with cmake and ninja. In an application...
