This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
Hi,
I have 52832(ble_app_multilink_central 12.2) which is connected to 5 51822 (experimental_ble_app_blinky) modules.
How to make 51822 not discoverable or not connectable...
Hi, I'm interested in the nRF5 SDK for AirFuel .
I have received a task to replace parts in a product which formerly used wireless charging and the CSR BLE chip.
I think...
If anyone will ever have this error:
When using c++ and singleton the use of operator new is not possible.
I found the solution in this post: forum.arduino.cc/index.php...
Hello everyone,
Lately I have been struggling while trying to run "BLE Advertising, a beginner's tutorial". My hardware consists of NRF51822 and PCA1000 dongle. I use SDK_11...
I am working through the TWIS Slave and TWI Master mode drivers Example using SDK 12 with the nRF52832 PCA10040 board and having issues. I am using Minicom through the terminal...
I want to use the last page of codespace for storing a single 32 bit word of non volatile data. I am failing so far and I think I just don't understand the page numbering...
Hello everybody
I am working with the Raytac BLE Module "MDBT40", which is based on nrf51822.
And I am testing example project "ble_app_uart" in the SDK6.1.0 now.
...
I would like to confirm my understanding of Problem sending 6 bytes to multiple services using sd_ble_gatts_hvx
I use nrf52832 sdk13.0.0
BLE SPI is master. I dropped...
Hello,
I connected the nrf module to jlink as described:
• vdd(nrf)-----3.3V
• gnd(nrf)-----gnd
• SDO(nrf)-----SWDIO(jlink)
• SCLK(nrf)-----SWCLK(jlink)
• 3.3V...
I've run into some interesting behaviour in my code and wanted to see if anyone can clarify for me. It seems as though the SPIS module doesn't set the MISO pin as high impedance...
Hello,
I built a simple I2C application for the LMP91000 and I was successfully able to configure it to read the status register.
However, I tested to see if I could...
Hi,
I used to use an imitated Jlink debugger to program/debug my target board(one Nrf51822 on it)
There are pins connection between them,it works just fine.
Now I...
