Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Using Command Line Tools 9.0.0 attempting to push code.
ERROR: JLinkARM DLL reported an error. Try again. If error condition
ERROR: persists, run the same command again...
Hi All,
I am attempting to use 6 PWM channels with the app_pwm library on the nRF52 and am only able to successfully get 4 pwm outputs. Upon changing the 6th channel (PWM2...
I need 3 time aligned PWM channels (period of all three channels needs to start at the same time) at about 100 Hz with 16 bit resolution on the duty cycle. I also need to...
hello,
I used nrf52 and softdevice 2.0.1 and i have a big problem.
For some times the BT works perfectly but after i connect more then 4 devices for some reason
the...
Hi,
I need to check the emission of my custom nrf52832 board design and I need an spectrum analyzer... To see if my design would pass the regulations and tests.
I was...
Hi Nordic,
It's hard to find an example to talk about the event of advertising. I checked the advertising chart and know I will get the event BLE_GAP_EVT_TIMEOUT. Where can...
Hi,
I attended a training session run by the BT SIG last week and met a helpful Nordic chap who, when I mused about how I was using a programming board to run a sensor...
Hi i am having doubt in RTC configuration.I am using RTC1 and i want to produce ticks for every 1 minute.I have combined the UART and RTC example to get the RTC output in...
Hello
i am using the Nrf52 with pca 10036 board. i am working on fruitymesh to work on visualgdb.
i am getting problem here
"#pragma pack(push)
"#pragma pack(4)
...
Hello, i need to count 1 or 2 minutes. Someone can recommend me if to do that is easier to use app_timer or RTC?
Which is the value that i have to put in the prescaler...
Hi,
I have bootloader ,Application with buttonless dfu (with FreeRTOS) and S132 v3.0,
Flashed SD3.0 and then bootloader with debug support. After updating application zip...
Hi all
I use the nRF52832 and the SoftDevice S132 V2.0.1. When I perform a soft reset (NVIC_SystemReset) while the SoftDevice is running, the fault handler is triggered...
Sorry i'm survey in forum ,and try for a week , the problem still there , please help me !!
I'm try to compile APP1 in IROM1( Start:0x1B000 Size:0x4650) ,APP2 in IROM2...
In Nordic's example GCC projects, the Makefile of the SD examples have -DSOFTDEVICE_PRESENT defined. However I noted that even though it is defined here, in nrf_drv_common...
I have a 1 second app_timer running which increments a 1 second variable used as unix time. We have a 32Khz Xtal, etc, which should result in good accuracy.
I have noticed...
