Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
Hi are there any image/bulk data transfer demo to test throughput between nRF and iOS application
There is one for older nRF5 SDK but couldn't find one for nRF connect ...
Hi,
I use two nRF52833-DK boards for uart communication (both using pin p0.06 for TX and p0.08 for RX), with their TX and RX and GND pins connected to each other, and perform...
Hello
I am facing issues while pairing nRF7002DK with nRF WiFi provisioner app, when I build the app (provided by nordic and hosted on github). However the pairing is successful...
Hello. On july 26 at the same hour, about 30 of our cellular modems stopped sending data. They are all using Verizon firmware. The units using Hologram firmware are still...
Hi
I have 2 BLE boards with some environment sensors on them.
I need to synchronise the 2 boards with < 1 mili second precision.
one board is configured as central,...
I am using an IMU sensor in sensor hub mode (LSM6DSV16X, LIS2MDL) with the FIFO interrupt interval set at 30 Hz. The data is sent over BLE. It works perfectly when using RTT...
Hello,
We are using Zephyr OS and SDK v2.5.0 on nrf52840 chip. We have noticed some delay between spi_write and spi_read of 29µs,which is critical for our goal. Comparing...
After I installed nRF Connect SDK 2.7 and tried to run the pre-release version of VS Code extension, I am now compleatly unable to make nRF Connect for VS Code function. ...
I' m using custom board of nrf5340 with nrf7002, and the SDK version is ncs v2.5.2.
I've tried to build and run, but the log in RTT viewer is only print the line "Bringing...
Hi nordic:
I am currently using NRF52833 to create a MESH product and would like Bluetooth to send AOA tag information in MESH mode. Is this feasible?
Best Regards ...
I encountered the following error while building my ZigBee app on a CI (dockerized Linux container), after bumping the SDK from 2.6.1 to 2.7.0.
The part "nRF52840" in...
Hi All, I am using an nrf52832 and using NCS version 2.6.0. I am having an issue where I am trying to initialize and run a thread, but the thread never runs. I have tried...
I want to set the CONFIG_CAF_BLE_ADV_FAST_ADV Kconfig option to make the Peripheral initially advertise with a shorter interval,but after adding some dependency configurations...
hello.
Currently I am implementing BLE Multi advertising in
NCS SDK: version 2.6.0.
I have a question during development through the samples/bluetooth/multiple_adv_sets...
Hello,
I am working with the USB CDC ACM Sample Application from NCS V2.1.0 on nRF52840DK and have encountered an issue when attempting to replace the UART_INTERRUPT_DRIVEN...