I would appreciate some suggestions on a good development flow to go from an Example to end application
I have nrf52832 on a custom PCB.
I tested several sdk13.0.0 examples...
If anyone will ever have this error:
When using c++ and singleton the use of operator new is not possible.
I found the solution in this post: forum.arduino.cc/index.php...
Hi I am using Jlink board, when connected to my pc, I can't select nRF5x programming.
Version I am using is 1.20.0.2. I tried the uninstalling everything and installing....
Hi guys,
In the iot sdk in mqtt.h there are typdefs for "mqtt_topic_t " and "mqtt_subscription_list_t".
I'm trying to set several topics (5) and subscribe to them.
...
Hi,
I am using nrf5832 that is running a coap server example.
I have modified it a little so it reads sensor data via i2c and returns the data using the coap callback.
...
Hi,
I would like to receive some suggestion about finding a CHEAP smartwatch / wristband already available that has these minimal features: BLE (with SDK / GATT profiles...
Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
I'm having a problem using SPI within Zephyr. My custom nRF52840 board has 74HC959 shift registers to drive LEDs. I'm using the SPI bus to transfer LED on/off states and can...
After clicking on ACTIVATE SIM and having correctly filled in the SIM IICD and PUNK I am receiving the following message: Request failed with status code 503 What does this...
Hello,
Using scan sample I am trying to read drone Remote-ID. When broadcasting Remote ID via Wi-fi Beacon no problems occur, but once selecting only Wi-Fi NAN as delivery...
Hey! I'm working on a LE Audio project utilizing the nRF5340, where I need to stream audio both from and to the nRF and I have encountered the error "sw_codec_lc3: LC3 enc_bitrate...
Hello,
I can see there are some ADC examples on Github https://github.com/NordicPlayground/nRF52-ADC-examples But those examples are nRF SDK5. Are there any ADC examples...
Hello everyone,
I have a problem using pstorage_update. Normally it does as it should, but once i call ble_stack_init(); on my code, pstorage_update doesn't work anymore...
Hey,
I am trying to use the example for Sync_Advertising_conn to get a connection between 2 nrf5340 devices. but I get this message
the problem is in the config
CONFIG_BT_PER_ADV_SYNC_RSP...
Hello,
I am using the nRF52811 on a keyfob that transmits short packets when a button is pressed. The button directly connects power to the MCU, and the firmware immediately...
Hi,
I've just received my new nRF9161 Development Kit, but when going through the Quick Start, it fails to program.
Log:
2024-06-19T20:51:59.582Z INFO Initialising...
I am trying to interface nrf52833 devkit with BG95 devkit using PPP connection. For this I am using gsm_modem sample code. But when I am getting error while build configuration...
Hi,
We are wondering the current consumption in our custom board. The board has the following components (my FW view :)
nRF9160 - powered directly from batteries (either...
Hi
I use nRF7002-DK and sdk version as v2.5.2,download lesson8 exercise 3 solution and build was error as below log, which parts am I miss?
build config as below
...
Hello,
I a working on a project that uses the nRF5340 CCM peripheral (Network core) in an asynchronous mode. That is, I encrypt PDUs prior to scheduling them for transmission...
I want to configure my setup for secure boot and enable TFM and encrypted application images for firmware update. I am using nRF sdk version 2.5.0. My board is nRF9160. Now...
I have setup the UART along the same lines as the sample project in the DevZone Academy. I have extended the example provided to suit the project needs.
What I am getting...
