Hi guys,
In the iot sdk in mqtt.h there are typdefs for "mqtt_topic_t " and "mqtt_subscription_list_t".
I'm trying to set several topics (5) and subscribe to them.
...
Hi,
I am using nrf5832 that is running a coap server example.
I have modified it a little so it reads sensor data via i2c and returns the data using the coap callback.
...
Hi,
I would like to receive some suggestion about finding a CHEAP smartwatch / wristband already available that has these minimal features: BLE (with SDK / GATT profiles...
Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
Hi,
I am currently working on a prototype with Silicon Labs Thunderboard sense. I am looking for a replacement product that has NRF BLE module. All I need is a BLE module...
I would like to hide BLE advertising from normal BLE devices.
And only be able to see such advertising with dedicated scanner.
I was thinking of changing access address...
Im making a project were i have two robots each one with a device connected with a mobile phone. But at same time i want that, when they are near each other they exchange...
Good afternoon! I would like examples of projects on Soft device S140 long range to test the work of BLE Long Range HCI-USB host - need to be able to connect to them. (scannable...
I'm trying to achieve as close as possible to 48KHz (or 24KHz) LRCLK rate, in 24-bit mode (MCK/LRCLK = 48), on an nRF52832. With the values defined in `nrf_i2s_mck_t ` the...
I want to use libuarte. Target is nRF52832 and SDK17.0.0.2. Do I need to take workaround against Errata109 when using libuarte?
And, I done backport libuarte to SDK15.3...
I have been using nRF Connect SDK v1.2.0 to program my nordic thingy 91, however recently whenever i open IDE, Segger Embedded Studio gives the following error,
"Unrecoverable...
I am new to BLE and I have some question regarding Mesh and LPN which we cannot get a consistent result :
Assuming in a Mesh set up there are 2 Relay units (simply refer...
Hey,
I have an OLED trying to use, that is built in with a pcb design.
I don't know the manufacture to contact,
On my PCB datasheet says: the OLED Module QT-2028TSWIG02...
I created a TWI software module which runs well as standalone. Now I need to put together with BLE code to comunicate with Android APP. I'm stucked because when I initiate...
I am able to provision and configure 1 mesh device with the nrfMesh iOS app. I am able to successfully provision a second device, but when I configure a second device, the...
Hi,
I am trying to test and develop the DFU-OTA in nRF CONNECT SDK for nRF52832
I followed these link to develop i am using NCS v1.4.2
1. I have copied the peripheral_lbs...
Hello, teams.
Now, I'm changing the Android studio source code.
when I changed codes, it changed right away.
But when I edited some other java files such as pertage8...
Hello,
We wanted to clarify the behaviour of the ESB retransmits when noack is set to true for the packet. This is because our system is very time-sensitive for certain...
I have modified the example ble_app_uart_pca10056_s140, which is a BLE peripheral example using the Nordic Uart Service (NUS).
The key snippets are below. If send_stream_flag...
Hi all. I hope you are well! I posted this in the backstage forum but I realize that is not where it should go ;) so I repost here. I hope that is ok.
page 56 in this...
Hi all,
I am trying to write an android app and (later iOS app) that can connect with the Bluetooth dongle and send data through uart, the Bluetooth dongle has been programmed...
Hello everyone,
i would like to update the sdk of an existing project from 15.3 to the newest 17.0.2. I am developing for the NRF52840.
I am using the serial port library...
