Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
I combined ble_app_hrs of example with ble_app_hts of example .
I write command in client characteristic configuration,
there is a problem that ATT_ErrorRsp : status...
I have some problem with Interrupt vector,details as below.
I design a bootloader code,and in the bootloader,i use timer0 interrupt.Then in the app code,i use the timer0...
Hi all,
I was wondering if I can install Soft device for a BLE-module other than Nordic?
And if so, will it gonna work?
Thank for help in advance!
blueguy
Hello,
I would like to detect a change in a pin( GPIO_IN_NUMBER ) and depending on it I would like to trigger a SPI transaction, this should happen through PPI.
So far...
I'm trying to migrate my old app based on buttonless app sdk13 to buttonless app sdk14.
I solved issuie according to migrate guide remove chunk things and etc.
My app works...
I am creating an App for iOS using nrf beacon.
App is for garage door and i want to get notification when door closed or open, when beacon is in range or out from range but...
I am using nRF 52840 board. I used Keil 5 to load one of the examples in SDK successfully, but when I unplug the USB cable and used the battery. My program doesn't run properly...
We worked on the nrf52832 DK.
We will begin the prototyping phase. But the dev kit's antenna is too big. Can send me a reference and schematic of a ceramic antenna.
Other...
We have based our code off of ble_app_proximity. Upon first connecting to the advertising NRF51822AB device with softdevice 110 v8.0.0, we write to pstorage.
static void...
I USE IAR7.7 AND v11.0
THERE ARE ERRS.
FS_REGISTER_CFG(fs_config_t fs_config) =
{
.callback = fs_evt_handler, // Function for event callbacks.
.num_pages = NUM_PAGES...
SDK Version: 13 Alpha
I've been able to track down, through app_uart.h, where UART interrupt priorities are set using NVIC_SetPriority(). Now I'd like to know where interrupts...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello,
I am evaluating the USB audio example from SDK v14 with an nRF52840-Preview-DK (PCA10056, V0.9.2, 2017.25).
SW9 is set to VDD power, SW6 is set to DEFAULT. The...
Hi,
I'm trying to setup Keil with PC-Lint using Nordic SDK11. I've noticed that SDK files contain a lot of PC-Lint annotations and I assumed that it should work but I'm...
