I would appreciate some suggestions on a good development flow to go from an Example to end application
I have nrf52832 on a custom PCB.
I tested several sdk13.0.0 examples...
If anyone will ever have this error:
When using c++ and singleton the use of operator new is not possible.
I found the solution in this post: forum.arduino.cc/index.php...
Hi I am using Jlink board, when connected to my pc, I can't select nRF5x programming.
Version I am using is 1.20.0.2. I tried the uninstalling everything and installing....
Hi guys,
In the iot sdk in mqtt.h there are typdefs for "mqtt_topic_t " and "mqtt_subscription_list_t".
I'm trying to set several topics (5) and subscribe to them.
...
Hi,
I am using nrf5832 that is running a coap server example.
I have modified it a little so it reads sensor data via i2c and returns the data using the coap callback.
...
Hi,
I would like to receive some suggestion about finding a CHEAP smartwatch / wristband already available that has these minimal features: BLE (with SDK / GATT profiles...
Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
Hi Team,
we are using the I-Jet Debugger with IAR IDE , How to load the Bootloader with this setup. Is there any additional settings required for this like Segger J-Link...
I have created code in GPIO read/write code with zephyr os. I did not add GPIO in .dts file. How the my GPIO example is working.
GPIO driver is not needed .dts support ...
Hello, All,
I am using the nrf connect tool on VS code for development, but i have a questions:
The west and some other python plug-ins used by this tool are installed...
Hello everyone. I am trying to develop a communication link between two nrf52 devices. I want to collect measurements from some sensors, pack them into a single data pack...
Hello,
I'm running Buttonless DFU successfully, but I would like to know if it is possible to start the application with the DFU service disabled, and activate it only later...
Hi, I have a firmware that runs well on nRF52833 dev kit (SDK 17.02) and I am trying to port it to a Laird BL653 dev kit. The firmware has a bootloader and it can perform...
so I use the default sdk in
D:\sdk\nRF5_SDK_17.0.2_d674dde\examples\ble_central\ble_app_uart_c\pca10056\s140
when i press button on nrf52840dk(pca10056)
it should at...
Hi,
I am evaluating the nRF5340 SoC and the recommended toolchain nRF Connect SDK (NCS).
I see that NCS is based on Zephyr RTOS, which provides also some drivers (spi...
Hi! I'm trying to save some variables after a watchdog reset for debug why my application hangs up.
I add a ram section on flash_placement.xml ( <ProgramSection alignment...
I am looking for Static analysis tool ( which is in compliance with standards MISRA-C and CERT-C) to be integrated with Segger Embedded studio.
Is there any preferred...
Hi
I am looking for a ways to perform DFU over serial, surprisingly i dont find any ways except this thread with no answers
https://devzone.nordicsemi.com/f/nordic-q-a...
Hi all:
About with the nrf_desktop example in NCS ,
I would like to modify the CONFIG_BT_HIDS_MAX_CLIENT_COUNT to '2' ,
so I add below command at "app_ZDebugB0.conf...
Can someone tell me the correct cable to connect the two boards together for debugging purposes.
There seems to be two main options, but its not clear:
TC2050-IDC-NL-050...
Hello, I experience some issues with NRF9160 and eSIM card. SIM_1V8 always output 0v and "AT%XSIM?" return "%XSIM: 0". I want to know if there is prior software configuration...
