Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
Hi,
I am currently working on a prototype with Silicon Labs Thunderboard sense. I am looking for a replacement product that has NRF BLE module. All I need is a BLE module...
I would like to hide BLE advertising from normal BLE devices.
And only be able to see such advertising with dedicated scanner.
I was thinking of changing access address...
Im making a project were i have two robots each one with a device connected with a mobile phone. But at same time i want that, when they are near each other they exchange...
Hi all! I am attempting to download a file from a web server to an NRF52832 using the Nordic IoT SDK version 9.0. Are there any good reference librarie? I found a few for...
Please help to understand. How to configure nRf24L01 receiver for 4-pipe (pipe 0, pipe 1, pipe 2, pipe 3 ). But most importantly, how to specify the transmitter settings that...
I saw earlier post on this blog and viewed on-line video for LitePoint OTA tester that claims to work with all BLE chipsets. We have multiple designs with different DTM interfaces...
I revisited SES to see if I could understand it better:
File/Open nRF Connect SDK Project...
I Pick Hello World and my left side Project Explorer window shows the zephyr...
Hi.
I have Bluetooth and ANT+ LEV working simultaneous and they work perfectly. Now I need to send to a Garmin GPS display several custom data from my EBike motor that ANT...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi
Is it so that the only way to use Asset Tracker 2 is with this AWS? Not even with the nrf cloud?
I am following your instructions here
https://nordicsemiconductor...
Hi all,
I use nRF52832 with the UART peripheral example.
I use SDK V15.0.0 and Softdevice V 6.0.0, with IAR embedded workbench version 8.22.1
Messages output with NRF_LOG_INFO...
Hi,
I am using the nRF52840, which has 256KB of RAM, (i.e. loads and load of RAM.)
I would like to allocate a buffer of 45KB.
I have tried using malloc (from the stdlib...
hello nordic! I am using NRF52832 to verify certain characteristics of BLE. the question is:After the BLE terminal device is bound to the mobile phone( Most likely Android...
I found this in the schematic and I wanted to
Confirm this is correct pinout to communicate over serial
Know where to go in the firmware to get this information?
...
Hi everyone,
I am working on nrf52832 using sdk15.0.0 using ble_app_beacon
I getting 3mA current when falling edge detected, i want to set my device as low low power consume...
Hi, Dear Nordic & All:
I use usbd_msc example to generate .xls file, and write content in it, sometimes I write successfully, and can open it right on PC with WPS，
but...
In project ,i use a TWI transaction manager to control two sensor devices.So, each device requires a GPIO to detect input interrupts. I use a GPIOTE IN event and a GPIOTE...
What is the drawback of setting the TTL on mesh packet to a high number?
I am assuming that a node will not relay the same message twice? I.e. it sees a packet for the first...
Hello!
I’m quite new to the nRF microchips and am trying to programme my nRF52-DK board following this guide ( https://infocenter.nordicsemi.com/pdf/getting_started_keil...
We are working on the OTA DFU of NRF52840. The soft device version we use is the latest: s140_nrf52_7.2.0.
Unfortunately, nrfutil does not have the code number for this...
