Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
Hi,
I am currently working on a prototype with Silicon Labs Thunderboard sense. I am looking for a replacement product that has NRF BLE module. All I need is a BLE module...
I would like to hide BLE advertising from normal BLE devices.
And only be able to see such advertising with dedicated scanner.
I was thinking of changing access address...
Im making a project were i have two robots each one with a device connected with a mobile phone. But at same time i want that, when they are near each other they exchange...
Hi all! I am attempting to download a file from a web server to an NRF52832 using the Nordic IoT SDK version 9.0. Are there any good reference librarie? I found a few for...
Please help to understand. How to configure nRf24L01 receiver for 4-pipe (pipe 0, pipe 1, pipe 2, pipe 3 ). But most importantly, how to specify the transmitter settings that...
I saw earlier post on this blog and viewed on-line video for LitePoint OTA tester that claims to work with all BLE chipsets. We have multiple designs with different DTM interfaces...
Hi Community,
I'm a little bit flyiing in the dark, so I like to ask this in the devzone.
Does anyone already implement NFC OOB Pairing and using Apple GymKit?
1...
We are not using the USB interface on the nRF5340, and thus are leaving VBUS and DECUSB unconnected. Can we also leave D+ and D- unconnected?
Thanks,
Scott
To the kind attention of Nordic support team,
I'm interested in understanding in a conceptual way, how the microcontroller is operating when sd_app_evt_wait is called. ...
We have the following setup: - Both nRF52832 and nRF52840 chips in our product
- The nRF52832 is a module while the nRF52840 is the chip integrated directly onto our PCB...
Hi,
Kit:nrf5340
SDK:nrf connect SDK 1.5.0
1.Can you please explain how the data transfer takes place in ble mesh while using nrf connect SDK.
2. Also tell me how...
The servo I use in my application uses a PWM signal duty cycle to represent servo amperage level.
So, to measure servo amperage, I use a GPIOTE channel to capture the time...
Hi!
I'm using ncs v1.5.0 and mfw 1.3.0 on a nRF9160 DK v0.15.0.
I'm using gps sample with supl_clint_library enabled
1. Things work reasonably well, but I am confused...
I'm trying to write a driver for an SPI peripheral.
west says:
```
../ncs/zephyr/samples/sensor/mydriver/prj.conf:5: warning: attempt to assign the value 'y' to the...
new uses SDK 17.0.2, SD 7.2.0
old target used SDK 15.2.0 and SD 6.1.1
Attempting to update BL, SD, and App over DFU.
1. If merging all new BL settings with SD, BL, and...
Hi,
I am using nrf connect SDK and compiling nrf5340 examples.
I want to implement a security related example in nrf connect SDK.
Can you please tell me
1. Security...
Hi,
I am trying to open serial lte modem app to evaluate power profile on thingy91. i am using toolchain manager (v1.4.99-dev1) to open Segger Embedded Studio.
While building...
This compiles with warnings and the value always comes back as 0
#define SW1_NODE DT_ALIAS(sw1) #if DT_NODE_HAS_STATUS(SW1_NODE, okay) #define SW1 DT_GPIO_LABEL(SW1_NODE...
Hello,
I have a application on a nRF52840DK as central. The code is based on the ble_app_uart_c example.
I need to send a lot of data through UART into the serial port...
I have followed various advice to create an SPI/I2C driver an own-designed device using the bme_280 example as a model
As this could be either SPI or I2C I put both configurations...
Hi all,
I am currently working on a project which uses the ble_app_uart_c example. I have a nRF52840DK as central. The central receives NUS pakets with a average data rate...
