Hi guys,
In the iot sdk in mqtt.h there are typdefs for "mqtt_topic_t " and "mqtt_subscription_list_t".
I'm trying to set several topics (5) and subscribe to them.
...
Hi,
I am using nrf5832 that is running a coap server example.
I have modified it a little so it reads sensor data via i2c and returns the data using the coap callback.
...
Hi,
I would like to receive some suggestion about finding a CHEAP smartwatch / wristband already available that has these minimal features: BLE (with SDK / GATT profiles...
Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
Hi,
I am currently working on a prototype with Silicon Labs Thunderboard sense. I am looking for a replacement product that has NRF BLE module. All I need is a BLE module...
I would like to hide BLE advertising from normal BLE devices.
And only be able to see such advertising with dedicated scanner.
I was thinking of changing access address...
Im making a project were i have two robots each one with a device connected with a mobile phone. But at same time i want that, when they are near each other they exchange...
Hello,
I am looking for (10) pieces of the tiny nRF52810-CAAA for a prototype.
Apparently, distributors do not yet have any stock and the lead time is 14-16 weeks.
Might...
This is probably a very easy question to answer and I apologise for not fining the solution myself but I have been trolling through the documentation for several hours now...
I am doing rapid development for a project, using the nRF52840 DK. Two key features are USB and BLE central role.
I started with the usb_cdc_acm project and am merging in...
Hi all,
I added newliib-nano to my GCC project, when I use new ( std:: nothrow) I got
I add some C++ flags and link flags:
custom-nano.specs:
How should...
Hello everyone!
I have been working on getting data from ADS1299 ( ExG bio-signal sensing). I successfully got data from this IC using STM32F407VG (Cortex M4) and transmitted...
Hi I'm using custom nrf52832 board, SDK14.02 and SES. I want use pwm driver to generate 2 channel pwm wave with custom nrf52832. Everything is working fine in nrf52DK board...
Hi,
I am to update the SD version that I am using, and in the documentation to create a firmware packet with nrfutil states that the table can vbe found with nrfutil pkg...
nRF52832 / SDK V15
Hello,
Is there is way to read the nRF52 flash memory (any location if possible) over UART without uploading a program in the flash memory for that...
Hello ,
I'm trying create a beacon Scanner.
I'm using the s130 protocol stack on the nRF51 DK , namely the nRF51422 SoC and PCA10028.
what I'm trying to achieve is...
I am trying to work through the MQTT-SN Examples that comes with the Thread SDK. When I use the prebuilt image for the Raspberry PI 3 board everything works great however...
Hello,
I use an I2C device to wake up a nrf52 microcontroler.
If I just use the init function
static ret_code_t twi_master_init(void)
{
ret_code_t ret;
const nrf_drv_twi_config_t...
Hi,
I'm using Segger Embedded Studio (with gcc naturally). The standard C++ exception handling doesn't work: exceptions are not caught by exception handler. Is there a way...
I have read a lot of the Dev Zone questions here about the RF Antenna design and read the PCB design guideline tutorials and skimmed some of the white papers. Of course the...
The current example TWI_handler will hang forever is it exits with anything other than NRF_DRV_TWI_EVT_DONE. This can occur if a TWI slave fails to acknowledge the address...
Hi,
Based on the electrical specification of nRF52840's HFCLk, the current consumption seems quite different depends which crystal is being used (attached the screenshot...
