Hello everyone
I'm currently trying to make dynamic endpoints on my matter device. I changed the .zap file to accomodate all the possible endpoints (16) with clusters...
Hi community,
I have a similar custom board as Thingy53, which has the nrf21540 module on board.
my purpose is to turn on the nrf21540 and do the reconnection, when...
Hi!
With the release of NCS 3.0.1, the required SEGGER JLink version to v8.18. pynrfjrprog is bundled with SEGGER JLink v7.94. From your website, it seems nrfjprog, being...
Hello,
Over the past three days (up until today), we've observed inaccurate behavior in the Message Routing Service. Specifically, we shut down our destination service during...
Hi,
I use the nRF54L15-DK flash fimware (.hex) with "nRF Connect for Desktop - Programmer" success.
And I view the schematic, discovered the DK board have flash memory...
I have a NRF9160 design with a TPS63031 regulator providing 3.3v. When my battery gets weak I am seeing spontaneous reboots, likely due to input voltage droop.
I'm experimenting...
Hi,
currently trying to boot up mcuboot with nrf54l15 pm_static for both cpuapp and cpuapp_ns. Both files are included in the zip file.
I have already tried several configuartions...
Hi,
I am starting a new iOS BTLE project for a new kind of music instrument. I started with the Thingy believing that that would be a good reference design to start from...
Hi!
Working on project based on nRF52810. Everything was fine until I began to work on part to save setting in flash memory.
I've used flash_fds example SDK 16.0 as starting...
Hi,
Currently I’m working on a device which is, on the one side connected to a smartphone via BLE and on the other side to another uC via UART.
Therefore, the UART speed...
I'm trying to get the debug version dfu secure bootloader from nRF5SDK160098a08e2 running on a nrf52832.
I'm able to compile it using cmake and a gnu c compiler. However...
So I am doing a project with a 160x80 TFT display, using the ST7735 driver. I have slightly modified the ST7735 functions to work with my display, and everything is running...
I am trying to create an application which would send data once a minute. The application is based on BLE advertising packages, because it should be the most simple method...
Hi,Sir：
I am making a DEMO based on SDK15.0(SDK15.0\examples\ble_central\ble_app_hrs_c) and pca10056 for my one of important customs.I need to implement some extra software...
Hi,
I am now in Hong Kong, and trying to connect to NB-IoT network here. There are 2 providers of NB-IoT in Hong Kong: "CMHK" and "Three". They provide NB-IoT since 2017...
Hi!
I was testing the SD Card example that is available on the SDK 13.00 in the following path: "nRF5SDK1300/examples/peripheral/fatfs". I checked SDK 16.0 and the code...
I have a hard-to-reproduce bug in my MQTT application that I have investigated enough to realize that my MQTT thread is stuck in a call to mqtt_publish(). I've verified that...
I would like to add UART as an option to the "ble_app_hrs_rscs_relay" example in SDK16, But keep the peripheral low power.
i.e. once I set a GPIO, the UART will start to...
I'm working on a project where UART0 is used as a nrf logger uart back-end. Recently I've tried adding UARTE1 to the project to implement additional serial communications...
I am unable to initialize soft device, but I am able to initialize log, led, gpio and timer as well, I can see debug prints as well. After debugging I found following information...
Hi everyone,
We are developing switch product which running with Android Application.
We have problem about send status from switch Device to Android Application
+ Android...
Hi ,
I have tested two boarrds(PCA10040) with same application id and higher application version,These work well done.Then I want to test mesh DFU Relay function,However...
