Hi, I'm relatively new to Nordic microcontrollers and have recently completed the beginner's course. Sorry in advance if I made an obvious mistake.
I am currently trying...
We are running a nrf54l15 board that uses an NFC T2T tag to encode a URI to open an application. We have noticed that sometimes, the current stays higher (~200 uA) after the...
I’ve got a bit of a hardware issue with the nRF52811 UART, receiving DMX data from a Chinese DMX controller.
Standard DMX data-rate is 250Kb/S, so the minimum bit time is...
Hi,
I am using the Nordic UART Service (NUS) peripheral and central on two nRF52840 DKs and I am developing with nRF Connect SDK v3.0.0 .
I can't manage to increase the...
I am getting an occasional softdevice assert on a BLE central device (hub). Both the central and peripheral devices are nRF52840 using Coded PHY and NCS v2.7.0. This error...
I am trying to keep nRF5340 in sleep state, and wake it up when there's a user input (e.g., button) and send a packet as fast as possible to iOS18. What would be the latency...
I have been following this tutorial by Nordic trying to install nrfConnect for VS Code, nRF Connect for VS Code, part 3: Building an application , but I am facing several...
I am simply trying to add a custom service to the HRS example. When I build in regular s132 armgcc it works no problem shows my blank service with nothing special. however...
Hi,
How can i disable peer manager from the buttonless DFU example. if just disable the peermanager by removing the code and editing sdk file, its not working.
i am using...
Hi All,
I am working on BLE+SD card.I am getting following error:-
*** Using Compiler 'V5.06 update 4 (build 422)', folder: 'C:\Keil_v5\ARM\ARMCC\Bin'
Build target...
I have a app that stores some calibration information in flash (1 page at 0x7F000)
When I booted now I noticed it has replaced it with "DEADCODE" following some hex number...
SDK version 12.2 and SoftDevice 132 and Dev. Board 10040
I am trying to run the ble_app_beacon example with NRF52832 DK. I have imported the IAR project into Segger Studio...
Hi,
I bought the nRF52840 in april. The problem is that my iPad doesn't detect the nRF52840. Also, when Itry to upload a .hex file on it, the board tells me that the upload...
Engineerings, We are looking around to find a way to prove that the hex file burned into the device is really the result of the original source code. Is there any idea/way...
Hi Guys, I try to implements the ctrl-C/V for bluetooth HID keyboard. But from SDK, I can't figure out how to send two keys. Even I do not use buffer_enqueue/dequeue in order...
Hello,
I try to build mesh sdk for nrf52840 it gives me error on RTT
0> <t: 0>, main.c, 318, ----- BLE Mesh Light Control Client Demo -----
0> <t: 0>, main.c, 108, Initializing...
hi, In my setup, I have a 3.7 V battery divided down to the bandgap range using a 100k and 100k resistors, so the voltage at the ADC input is 3.7 * (100/200) = 1.85 V. I am...
Hi
I used "nRF5_SDK_for_Thread_v0.10.0 - cli sample code and try to test Thread command "diag"
when I type "diag" then it will show "diagnostics mode is disable".
...
I am working on a project which involves sending data from many beacons to many other beacons. To be more specific, I have two groups of beacons:
The first group consists...
I'm planning to use one of those beacon platforms:
www.ebay.com/.../352167746226
www.ebay.com/.../112493464451
for a close proximity positioning system now I'd like...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
