i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
I'm developing the PCB schematic for a system using the nRF52 and have some questions on the SWD programming interface.
It seems that I only need 4 pins for the Segger...
Hello,
I am curious, does nRF52832 support USB Type-C in terms of data transfer and Power Delivery? Or will I need another MCU to handle data transfer and Power Delivery...
Hi,
We've developed a custom board with buttons(peripheral) which will talk to another custom board operating as a repeater (central on one side to talk to our custom board...
Hi,
What are the possibilities for flashing a new nRF52840 device on a custom board. Do I need the jtag interface or does the device comes preloaded with some wireless bootloader...
Hello everyone,
I have interfaced an encoder and speed sensor on a spinning bike that all connect to arduino via COM/USB port. The COM port communicates to a game engine...
Hi, I am using nRF52840 kit and using Ubuntu Host PC. I am running usbd_cdc_acm_example with below link :
https://www.nordicsemi.com/DocLib/Content/SDK_Doc/nRF5_SDK/v15...
At nRF cloud introduction pag, I got the impression the "nrf cloud" front end source code is/or will be available in open source.
Am I correct? The nRF cloud source is...
I am using nfc_t4t_lib and I need to send a response 100ms after I receive the NFC_T4T_EVENT_DATA_IND event. How do I extend the response timeout by sending S(WTX)? There...
Hello,
As nordic has implemented sdk for mesh and i have been using mesh sdk v3.0.0 LIGHT_SWITCH_EXAMPLE but i am facing some problem regarding pa_lna. Actually wt i have...
Hi,
I am testing my I2C function by using ".examples\peripheral\twi_sensor" of SDK 15.2.
Because my SDA and SCL is define in P0.04 and P0.02, and my I2C Slave is MPU6050...
Hello,
I would like to know that what are the provisioning parameters needed to add an Unprovisioned device into a mesh network?
Thanks and regards,
Jahnvi.
We, I am using nRF 5 SDK v 14.2.0.
This time, without using WDT, using only the application timer, We are developing a process to send data by detecting acceleration and...
Hi,
I'm currently trying to implement Peer Manager in my existing project, for both pairing and bonding. I'm using the ble_app_template in examples/ble_peripheral in the...
Is it possible to use the TWIM and TWIS at the same time with 2 different I2C buses with openthread.
I tried this with THREAD SDK 1.1 and had link problems because of the...
