Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
The pin connected to lis2dh12's int pin consumes about 300 uA.
But the pin I used as button,also enabled int function , works good.
The pin I used as wake-up is in input...
In order to establish a wireless connection from my pca10056 developing card and a second nRF52840 SoC module using example CLI commands, and then being able to check/set...
Hi,
I have few queries regarding the internal regulators of nRF52840.
1) Is it mandatory to configure the internal LDO or DC/DC regulators of nRF52840 ?
2) If these...
Hi,
As mentioned in the Ch. 5 "nRF52840_DK_PB_v1.0.pdf" Section 5.3 in "high power mode the external supply should be connected to just the "VDDH" pins and "VDD" pins not...
I want to write to nRF52840 the example "ble_app_hrs_pca10056" from nRF5_SDK_15.2.0 by command line.
first I merge 3 hex file (bootloader, softdevice and app) with the command...
Hi,
I'm developing BLE 5.0 applications as a peripheral on nRF52832 under Windows, based both SDK14 and SDK15 (Softdevice S132).
I don't have any smartphone that supports...
Hi every body,
There is a problem with pwm driver example in demo3 part! after downloading, the board led is just on as it must, but after changing top_value there is no...
Hello everyone, I am planning to use the nrf52840 with the ECG sensor ads1298 (AFE for 8 channel ECG). The sensor interfaces via SPI to nRF52840. Has anyone worked on ECG...
Hi all,
I am working on nRF52832, nRF5_SDK_15.2.0, nrf5SDKforMeshv300src, softdevice_6.1.0 and communicate with CAP1214 device.
When I erase all flash on nRF52832 and...
Hello all,
I am using nRF52832 IC, Segger ES as IDE, SDK 14.20 and SD v5.0
I have around 70 bytes of data to be sent to a smartphone. I am using nRFConnect app to check...
Good afternoon. I need to make a network 5 or 6 nrf52840 boards connected as peripherals on a single central board, also of nrf52840. Each board will read a sensor, and send...
because I cannot find nRF module for testing.
and I want to use bluetooth 4.0 BLE with nRF uart
so my product will send data from serial port (rx ,tx through DB9 ) and...
Hi there, We are not using external Crystal for this design and thinking of reusing XL1 & XL2 (Pin 0 and Pin 1) for SPI (MISO & MOSI). But I found that I can't set properly...
So we're in production with the '832 and me, I drank the kool-aid already, but I'm trying to turn my cow-workers on to Nordic so I tell one of them "Oh install the command...
