Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
Hello,
I'm trying to get the SPI drivers working in slave mode. I have tested my master (Atmel L21) on an Arduino and I can see my message clearly. I'm trying to get nRF52833...
Hello
I want to access to the buffer to see what I am transmitting for then change the data to transmit to be able to verify, also I want to know where I can find de Kconfig...
Hi!
I have a custom board with a NRF52840 and some extra sensors for my application. I'm trying to comunicate with one SPI sensor but I have a little extrange behavior....
Hi,
I am trying to create a combined Bootloader + Bootloader Settings + Application hex file to flash the same into the devices during the production.
Bootloader Project...
i write 40bytes to flash 0x74000 and read 0x74000。i find it actually use 160bytes. I try to write a different number of bytes, it actually use 4*(write bytes)
this is...
I wonder if I can use spi1 or i2c1 on nrf9160. I use the 9160ns board configuration but non of my configs work for spi1 or i2c1 works. If I change it to i2c2 or others it...
I have a startup sequenced (nRF52832 peripheral) based on the s132 (v7.0.1 BLE 5.1) NFC Pairing example where it advertises at 1Msps link rate, then uses the PHY UPDATE API...
Hello!
We are working with NRF52840 dongles and want to be able to have them relay data over an OpenThread mesh network through UDP automatically. We have found within...
Hi,
calling "nrf_ringbuf_get()" immediately after "nrf_ringbuf_cpy_get()" returns an invalid pointer to the data. A workaround could be to assign "rd_idx" to "tmp_rd_idx...
Hi to all,
I have designed a custom board with 3rd party module (RAYTAC MDBT50Q) which includes NRF52840. During debugging on the custom board, two modules were demaged...
Hello,
I am using serial LTE modem for communication.
After trying to connect to TCP server using AT#XCONNECT I get following error:
The only official documentation...
In a system based on one nrf52-ble-app-uart-c-multilink-master and multiple ble_app_uart, the data from any entity is sent to all devices.
i.e. each ble_app_uart is sending...
Hello,
I'm using BLE peripheral device. I need to connect it to a BLE central device and exchange data. There are some connection procedure-
1. Discovered Bluetooth devices...
Hello, everyone, when I call err_code = fds_record_update(&record_desc, &record), I sometimes get an error: FDS_ERR_NO_SPACE_IN_FLASH.
Therefore, when this error occurs...
I have the nRF52 PCA10040 DK device, and I'm downloading the code from the online mbed tutorial. I'm using Putty serial port to communicate with the device at 9600 baud rate...
