hello, im from india im using nrf24l01+ for my project to transmit and receive data between two arduinos. i tried all tutorial basic programs but i cant sucessfully send and...
I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi,
The opcodes for Generic Power OnOff models are wrong. They weren't changed when the model was copied from the Default Transition Time server Model.
From the Model...
Hi，
My english is not good, please forgive me.
msd and hid device，set as follow:
//msd-------------------------------------------------------------
APP_USBD_MSC_GLOBAL_DEF...
Hello,
i'm practice beacon on 51422 DK. The first thing i wanna try is GPIO setting. What else i have to write or replace from the beacon example after setting GPIO in ...
Hi, I have working firmware for nRF52832 dev kit based on mesh coexistence examples (Mesh SDK 2.2.0 + nRF5_SDK_15.0.0). I'm trying to port the same firmware on nRF52840 dev...
I have flashed the firmware using nRF connect app. I have a bat file which executed few commands. I want to transfer that file to flash memory and access it I the file explorer...
Hi there!
I am trying to add custom UUID's for my BLE application.
I have a custom service which has 2 RX and 3 TX characteristics.
I have a situation where the Android...
Hi,
I would like to disable TWIM peripheral when not needed to save some power and enable it just before it's needed. Is there any delay after writing to NRF_TWIMx->ENABLE...
I want to get vdd without timer
so i found this.
https://devzone.nordicsemi.com/f/nordic-q-a/38239/nrf-52832-saadc-without-timer/147517#147517
and change some part like...
I have a design, using the NRF24L01+, that I would like to run from batteries. The Transmitting device is not a problem, because it can turn off when not transmitting.
For...
Hi All,
For NRF52 is that possible to configure the system to use a different pin for RESET than GPIO 21? We want to reset the NRF on errors, if our other MCU detects some...
Board：PCA10056 （0.9.3）
SDK：15.2
Softdevice：S140
Example：ble_app_blinky
Today，I follow this page Using an ampere-meter for current measurement to measure the current...
Used SDK: 15.2.0
Hello,
I want to print some debug messages over RTT after an error occured. After that I want to reset the system.
If I put the string into the que...
I've followed the steps to set up the SDK.
When I execute the batch file(setup_sdk.bat), there is something wrong occur (as below pic)
I've installed the git and add...
