I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
In our project we have functions for outputting a single frequency via PWM for an indefinite amount of time until we call a function to turn it off. See attached code.
...
I have a product which uses the nRF52840 SoC that will also have NFC functionality. The housing of the PCB is sort of forcing a custom design for the NFC Antenna.
We need...
Hi all,
I'm new to the nRF SDK and am currently tinkering around with my nRF52840DK to build a DIY Matter sensor. I copied the sample from the SDK, expanded it to my use...
Hi,
I am working on a custom nRF52840 design (using nRF Connect SDK v2.9.3) and I have accidentally locked the chip via APPROTECT.
My major issue is that on this hardware...
Hi, I am unable to read GPIOs (always getting 0x00000000 from gpio_port_get or 0 from gpio_pin_get). My main project is https://github.com/marcuswu/leaf-fall/tree/main/firmware...
After installing nrfutil-ble-sniffer v0.19.0 (released 2026-04-30) and running bootstrap, Wireshark does not show the "nRF Sniffer for Bluetooth LE" capture interface. The...
Hello everyone,
I'm working with the nRF5340 and I would like to connect a LIS2MDL sensor(see the schematic below).
The sensor has two power pins: VDD and VDD_IO . Initially...
I've been living with this for a while now, but it's getting annoying very quickly. I have a project in VS Code that uses the nRF Connect extension to build for nRF52832 and...
Hi
I want to use the FEM 21540 with nRF54LM20.
My overlay is :
My config is:
I think this should work because my nRF54L15 DK works well with this.
But it is...
Hello everyone,
I’m currently porting my old projects from NCS version 2.9.0 to 3.3.0.
In doing so, I no longer want to use the outdated Partition Manager; instead, I...
Hello. I used the "peripheral_nus" example for nrf52840 - everything goes as it should - I connect via bluetooth and the "nrfConnect - mobile" application receives the message...
Hi Team,
I am working on an nRF52811-based BLE application using nRF Connect SDK (Zephyr) and facing an issue while trying to store the device name in flash using the Settings...
Hello Nordic Support,
I am currently re-qualifying our Bluetooth product in Bluetooth SIG Launch Studio because we had to migrate from NCS SDK 2.1.4 to 2.9.2 due to a security...
