I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hello Devzone,
Our research group is using the NRF52832 chip embedded in a flexible substrate to transmit EMG (muscle) signals via Bluetooth. We’ve been having a couple...
I have been trying to find a solution for this but to no avail. I have nrf connect 3.10 installed. I am trying to flash my compiled code but keep getting the error: Unsupported...
In general, it's not a question, but the only suggestion for SDK developers how to improve debugging way.
So, while implementing DFU upgrade in my project I faced to the...
Hello everybody,
My project is based ble_app_eddystone example and nRF5_SDK_17.2.0 SOC is nRF52832.
Beacon advertise Eddystone UID +Eddystone TLM +Eddystone URL, works...
Dear,
how to change the adv. timeout setting and disable uart0 and uart1 in ncs v1.6.1?
I use the nRF5340 and example peripheral_lbs.
The path is as below:
nrf\samples...
I am using the following CAF modules on nRF52840DK, ncs 1.9.1: Buttons, LEDs and Power manager (see attached project caf.zip)
Button 1 is used for ON/OFF fuctionality. When...
I submitted a project idea for the Electromaker make it smart thingy:91 contest. Part of that was to detect and alert a user if there was an impact. This would require access...
How do I find out which peripherals are available at the same time?
Somewhere it was mentioned, that peripherals wit the same "ID" are on the same HW and only one of them...
Hi,
What's the max range achieved with BL5340 (With PCB Trace antenna) in indoors and Outdoors when advertising and connected mode? (With 1M,2M and Coded PHY(125Kbps,...
I use nrf connect sdk 1.9.0, to run periodic_adv and periodic_sync example.
The adv side sends this data: mfg_data[] = { 0xff, 0xff, 0x00 };
But in sync side in scan_recv...
Hi,
My mesh project is occasionally suffering some dropped messages and after probing around I found this on one of the nodes.
I have four nodes and one gateway running...
Hi,
In nrf52840 dongle, I use nrf_crypto_ecdsa_sign function to sign.
Everything is fine in when building, but when testing the real world data, it’ll will show error...
I use 52820 to do ble_usb+esb project, but I have encountered problems when adding USB. I have added USBD_HID_COMPOSIT in the project of \ examples \ peripheral \ usbd_ble_uart...
Dear community
I am developing an autarkic embedded system where I harvest energy from a thermoelectrical generator. It is a simple application, I need to acquire the open...
