Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
I'm trying to build "application_update" sample. I created a new application from sample. added build configuration for nrf9160dk_nrf9160_ns board and changed to variables...
Hello,
I have the Feeling with nrf connect programmer you can't select the Network core.
I use Programmer Version 2.2.0 and have our own hardware but also the nrf5340...
Hi Dev team,
I have been working with code development using Thingy91 and NRF Connect for Desktop. I use GitLab to maintain and manage my codebase.
I wanted to use GitLab...
I have nrf52840 pcb without xTAL.
In this ticket ticket I have discused about start Zephyr project without XTAL onboard.
But now I faced with other issue to start mcuboot...
Hi everyone,
I'm using nrf52840 as a connectable advertiser. Used ble_app_blinky example with some modifications. And I reduced the advertising interval to 2 seconds....
Hi, I'm using the example "libuartes" and developing 2 UARTE. But I dont know how to recoginize what port are communicating with external device because I only have 1 uart_event_handle...
Hi, Im trying to use nrfjprog from inside a docker container (ubuntu). I have started the container with --privileged and it seem to work but when i try to run the container...
Hello.
I use nRF52832 with SoftDevice and several TWI-connected IC's.
The power consumtion of nRF52832 is 14 uA after TWI initialization (low power mode and DC-DC regulator...
Hello, i have six buttons on my custom board, these buttons are inited with following code:
(there are pull up resistors present, hence NRF_GPIO_PIN_NOPULL is used)
SEGGER_RTT_printf...
Hello,
We are using nRF52840 chip for a power-sensitive application.
We use the UART which is connected to a LoRaWAN module.
Now when I enter the system ON mode after...
Hi,
I just started working with Zephyr and having some problems right out of the gate.
Board: Nordic nRF52840DK Example: i2c/spi_fujitsu_fram Branch: Main
When I'm using...
Can Nordic team be sure that SweynTooth test team has tested Nordic chips? If so, the claim in Nordic dev zone that Nordic chips are not listed indicating Nordic chips are...
I have followed Einar's response on the below thread but I still cannot see the logs on the SES
https://devzone.nordicsemi.com/f/nordic-q-a/79682/adding-mcuboot-bootloader...
Hey devs,
I'm trying to get the i2c interface to work with the MP8862. I followed the TWIS driver guide to get started and in there everything worked.
Now I wanted to...
Hi Everyone,
I'm using VS Code, nrfConnect SDK v1.7.0
I'm trying for minimal bluetooth roles(either central/peripheral) along dfu support in nrf52820 chipset.
when I...
