Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi there,
I need realtime data monitor, but the power consumption is too large when BLE sending data continusly. So I wanna know wheather NRF52832 support package the...
Hi,
I am not yet familiar with NFC.I s it possible to read battery data from the NFC tag of the nRF52 to another device (for example a smartphone). I want to write simple...
Hello,
I am in the process of designing a new custom board with the nRF52832. Apologies for the silly question, but swimming in the documentation at the moment, and I need...
HI, we want to develop DFU over NBIoT network (UDP), and we would like some advice on how to implement that. We are using nRF52832.
Looking at your SDK examples for BLE...
Hello Everyone,
I am trying to integrate LIS3DSH accelerometer with nRF52832 development board(I2C communication). I have Implemented Wake-up State Machine for LIS3DSH....
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Hi folks,
I've found no beeter way of reporting this (no public SDK repo which allows issues with code reference).
I tried to TX ESB DPL frames from an nRF52840 to different...
Hi all,
I want to sell a device that I have made that uses the nrf51822 and the app inside the chip is derived from the ble_app_uart. It uses two chips that communicate...
When I send my app to people, it uses a specific version of pc-ble-driver. I would like to make sure dongle used was programmed with the hex file package with this specific...
Hi,
I'm having issues with my nRF9160. I followed the steps under "Getting started with development", but I keep getting the following error when updating the mfw:
I...
Hi
I'm using the NFCT peripheral of the nRF52832 Rev. 1.
The state machine (figure 118 in PS V1.4) shows that the NFCT can be activated by either issuing the TASKS_SENSE...
Hi ,
I am using the secure bootloader example (SDK 15) as a template for my DFU solution.
I am experiencing issue with the update process as the device shuts down after...
Hello
In our project we are using NRF52840 SoC.
Up to this point NRF52840 chip is used as BLE module to be able to connect our device to cloud over gateway.
now we are...
I have added DFU service in my custom application and I am able to upload the zip file of my application over the air by connecting to the DFUTarg using nrfconnect in my mobile...
I'm developing the PCB schematic for a system using the nRF52 and have some questions on the SWD programming interface.
It seems that I only need 4 pins for the Segger...
