I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
I am using nRF52820 and the SDK is nRF5_SDK_17.1.0_ddde560. When setting advertising data, I am trying to enter the chip's BD address for individual identification. Is there...
So, I follow the zephyr docs ( https://docs.zephyrproject.org/latest/kernel/services/synchronization/events.html )
and define an event as:
However I get the error: ...
Hello, when building the MQTT sample in the nRF Connect SDK, `getaddrinfo()` is returning only -2 when built for the nRF9161 dev kit. I'm using the onomondo SIM that came...
Dear DevZone Nordic Team,
I am currently working on a project involving the nRF9160DK , and I need guidance on how to operate and output GPS values in the debug console...
I am learning how to use MCUMGR. I generally understand it, but I have some concerns.
- The firmware with the private key can also be overwritten. Then it will not boot...
Hello:
We know that 45pin 46pin DEC4 can be connected to inductance to process the ripple of internal DCDC circuit. Then, may I ask which pin is the input power supply corresponding...
Hi,
Can someone please help me to understand how to implement secure boot on nRF52833 chipset?
How to secure root of trust, as once you remove the protection, entire...
With TAU set to 24 hours, when we wake up every 8 hours, everything works fine. When we extend to 12 hours, it takes longer than 10 seconds for a connection to be established...
I successfully enabled littlefs in mcuboot and read/write it successfully (due to project requirements), and then tried to enable littlefs in both mcuboot and app, operating...
Hi,
I am planning to design a new PCB and transition from using the Raytac module to our own custom PCB.
During my search, I found a design that includes an SMA connector...
Hi, What I noticed is that every time I want to flash the nRF9161dk I need to do `west flash --recover` for it to work. I am flashing from Mac M1 (Sonoma 14.5) with `West...
nRF51822QFAC SDK v10 S130
In the completed project it was necessary to make an update. It is necessary to switch off the softdevice and switch to its own Rx protocol. After...
Just purchased a nPM1300 v1.1.0, but it will not connect to my computer. I am using version 2.6.1 of nrf connect, v1.3.0 of the PowerUp app, and what I believe is the correct...
Once the modem is turned off (e.g. using at+cfun=0) - what will be the state of the MAGPIO pins? Will they be pulled to GND or will they float?
Thanks
Ulf
P.S. The same...
Hi,
I am trying to implement the scan delegator in the broadcast_sink of the nRF5340 audio application.
Currently, I am adding the advertising feature in the broadcast_sink...
