hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Hi,
I ran some tests with the SW and HW crypto on nrf5340dk. I expected that using the crypto cell would improve my crypto performance tremendously but unfortunately,...
Dear friends,
My 52840 DK flashed a serial example( nrf5_SDK_for_Mesh_v5.0.0_src\examples\serial ) as a provisioner.
We use PyACI communicate with provisioner by Uart...
Good evening,
Referring to the following page which lists IDEs that are supported by Nordic Nordic Supported IDEs
Please kindly let me know if the following toolchain...
Hello,
first I have to say that I'm new with nRF5340, Segger Embedded Studio and Cmake.
I have a working project with CMakeList.txt. So I include it into Segger Embedded...
Hi.
I am trying communication from nRF52832 to iPhone using ble.
I use main function which put in nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_uart.
But,I...
Hello,
I have done the setup of Lsm5dsl with Nrf52832 DK board but I little bit confused about what hardware configuration is there so please guide me.
This is Code...
Hello Nordic great team,
We have a question please, we would like to configure our IOT device through the air, and the best way as we see in our use case, is to use the...
Hi there,
I tried to configure the openthread co-processor radio.
The build went well for my nRF52840 dongle, I managed to generate the RCP package image but when I install...
Hi!
I'm working with the nRF52833 in a Laird dev kit, the bl653_dvk and I cannot build a Hello World with mcuboot application in nrf sdk 1.7.0 or greater.
Although in...
Added the below lines to the peripheral_hr and I could see the logs without any trouble.
Same lines added to the central_and_peripheral_hr and I can see anything. What I...
Does someone have experience driving several slaves on a QSPI bus? Can we use a general IO pin for Chip Select (CS)? [Edtit] (I believe the nCS - QSPI pin described in the...
Hi,
I am trying to filter an iBeacon sample using a modified version of the central_hr_code.
Changes on the central_hr_code:
Added 128-bit UUID definition:
Added...
Hi,
I am developing a health wearable and want to store biosignal data into flash and then read at some point. I found that the reading process is relative slow as I tested...
Hi,ALL:
I use esb 2.4G liberary,and I found the same kind of produc build of nrf52840,it's radio current consumption is 1.2mA-1.3mA,how can it do it? My project is build...
