hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
On the nRF 52840, is there a way to have the TWIM peripheral suspend a transfer after transmission of a single byte? The TWI peripheral provides the BB_SUSPEND short, but...
Hi engineer,
i am running a example:SDK 12.2/ANT/ant_bpwr,MCU:NRF52832;i want to dynamically modify the value of "CHAN_ID_DEV_NUM" by reading the UICR value for distinguishing...
I am trying to figure out how to use the SAADC component of the nRF52840 to measure an analogue input and report it as an attribute in a Zigbee end device. I have, so far...
Hello,
I am analyzing the DKs power amplifier characteristics as an assignment for university. I got the serial_lte_modem running and send AT commands via UART from an external...
Hi,
I am looking for a 4G module with in built gps in it. It has to work in european market, need to have esim facility.
Can you provide with the product links.
-
...
Hi, I am trying to code an AoA transmitter using the direction_finding_connectionless_tx sample project as a basis. I am using nRF Connect SDK v1.6.0 with nRF52833.
I am...
Hello,
I am having a few problems when trying to check if the nrf52 is dfu mode with my python script.
For that i was trying to get the firmware version from the dfu...
On Mac OS X Big Sur using the nRF Connect 1.6.0 installation in Segger the documentation suggest that to add a new source file to a project one should right click the project...
Hello, I tried to run the following command on my nRF52832 today and it reported an error.
The operation before the error was: I enabled APPROTECT, and when my colleague...
Hi, I made a mistake while working with a custom board.
I run "nrfjprog --recover", which obviously clears UICR, and then I powered the board off without writing the new...
I have a custom board with 3 nRF52840 chipsets, 1 central module is connected to 2 side modules.
The central module communicates with each of the side modules using UARTE...
Hi!
There is an end device that measures the temperature. If I calibrate the ADC during initialization or immediately after startup, the program hangs. If I start the calibration...
Hi Team,
I am trying to make RTT in debug terminal instead of debug serial port i was add all rtt files in the project tree but it was not shown in cmsis configure wizard...
Hello everyone,
I am trying to implement ECDSA_P256 in my code by using the nrf_oberon libraries.
What I have to configure in order to use these functions?
Regards ...
