I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
Hi Nordic,
I am trying to use the nrf52840 to talk with my 4G module on baud rate of 115200 , but I find it always come into error for the recving the uart data. Also it...
Hello,
I have an nRF9160 development kit and was measuring the time it takes for switching off the modem
when it has an open data connection.
I did it by sending an...
Hi,
I'm currently working on NRF52832 (Softdevice s132 6.1.0) controller and developed a firmware from light switch client to develop a mesh network and its working fine...
Hi sir,
I have downloaded the NORDIC THINGY52 SDK from the given link https://devzone.nordicsemi.com/f/nordic-q-a/51236/unable-to-compile-ses-project-in-thingy-52-sdk (As...
Hi,
What do I need to be able to FOTA when nRF Connect SDK is updated?
For example, when the SDK version is 1.6.0, can I use the changes I made to the new SDK version...
Hi, as the table register above, If I want to set Tx_Gain manually, Does MODE effect my config? (Ex, if I choose mode as 0, does the device use POUTA default to use instead...
Hallo,
I am trying to communicate MAX86140 sensor with nrf52840DK. This is the link to the datasheet of MAX86140/1 . I am able to write and read MAX registers successfully...
Hi,
We are using mesh SDK 5.0 on NRF52840, We need to add about 30 groups in subscription of a node.
Using the provisioning app, we can add about 30 groups in subscription...
Hellou, i have questiuons about NRF MESH SDK 2.1.1.
We have in production street light based on light_switch_server_nrf52832_xxAA_s132_6_0_0 from NRF SDK 2.1.1.
When we...
Hi, I'm new to the Nordic Eco-system, but we are working to use nRF52811 in a proprietary beacon solution.
We are tying to modify the "Heart Rate Service" example to best...
I've developed a custom service and DFU using secure bootloader. I've started developing it for nRF52832 and all was working. I was able to generate .zip file and update the...
Hi,
Kit : nrf5340
SDK: nrf connect SDK
I While testing the timeslot example in nrf samples part, I am getting the below error. Kindly tell me the procedure...
Hi!
I'm close to finishing a project where every type of messaging is done using simple BLE broadcasts (using my own frequency hopping and other features.)
However I...
Loss of comms between nRF24L01+ transmitter and receiver after successful data transfer.
One rf24 is configured as a PTX (sensor device) communicating in a simple point...
Hello,
I need to implement, say, 100 LPN + proxy and 1 friend + proxy, LPN are metering devices.
How can I send a value from a sensor to my phone without sending a request...
