Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
hello, im from india im using nrf24l01+ for my project to transmit and receive data between two arduinos. i tried all tutorial basic programs but i cant sucessfully send and...
Hi!
Since I do not have a SIM card that provides support PSM or eRDX I need to switch the system mode manually.
In my config I have CONFIG_LTE_NETWORK_MODE_LTE_M=y ...
I generated boot-loader (logging disabled) from SDK 12.1.0 for adding a signature check during DFU for nRF51
The problem I am facing is with the size of bootloader (hex...
Hi I checked the relevant topics in the forum but none of them fixed my issue so I just create a new one here.
Basic info:
Hardware: nRF52 DK PCA10040
SDK: nRF5_SDK_15...
Hi,
I'm having issue connecting to the nRF52840_DK through J-Link and nrfjprog. I was able to connect to it the first time and upload simple BLE sample, but afterwards I...
Hello,
I'm developing an app for nRF Connect Desktop based on the nRF Connect Desktop BLE App.
I would like to find a characteristic item based on an UUID. Where is the...
How is it with SUPL and NB-IoT, will it work? AFAICS, in the example code, the supl_support code only uses TCP, and this is not a protocol supported when the device is using...
<Environment> - Windows10 - nrf v1.3.0 - modem fw 1.2.0
I'm attempting to make a socket and communicate with the modem using it.
However, sending data doesn't work out...
Hi everyone,
Looking the nRF52840 Product Specification v1.1, I see that there are several System Off modes.
1. Using the function sd_power_system_off() what is the by...
Hi,
i'm new on using nRF5 modules and i have some question about how to program the nRF52840 on a custom board, so with a completely new chip.
Reading the schematic of...
I am using nrf52840 DK (pca10056) board and nrf5SDK 16. There is one low power sensor connected to the board via SPI interface. My program consume less than 30uA before I...
HI:
I transfer the init packet and firmware to bootloader successfully by UART DFU, and then the app can not start. It report error as below:
<00> info> app: Inside main...
Hi All,
My update of nRF Connect v3.3.0 failed after a while:
Update of nRF Connect failed with the following Error-MSG:
On the same day I got an install from Oracle...
Hello everyone,
I would like to use the PPK with a NRF52 Dk, but I have external sensors connected to the VDD and 5V, so when I will plug the ppk I will have to disconnect...
Hi,
I am reading a 24-bit data from SPI by getting a data-ready interrupt from GPIOTE pin in a NRF52832 chip. I have to buffer data for the BLE interval duration then send...
