here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi All. In my final project (Electrical engineering) I'm trying to create a Closed area navigation system using AoA/AoD methods. (e.g., https://www.youtube.com/watch?v=zg9IBP3WRCU...
nRF52804 SPIM3 not work. (SCLK/MOSI not output)
However, if I debug it using jlink, it works.
My environment is nRF52840-DK(PCA10056/v1.0.0) nRF52 SDK 17.0.2
My program...
Dear Nordic team：
The APP on the ios 16 system of iphone connected to the ANT+BLE parallel bicycle number table，but automatically disconnects after a normal connection for...
Hi there,
I am looking to tune my antenna. I searched in the documentation how and I found a page without values. Can you please give me some guidance?
Our product is...
(What I want to achieve is to be able to use the USB pins (D+/D-) for debugging on a PCB using a nRF52833 QFN40 MCU. I currently use UART through two regular I/O pins for...
Guys,
I'm stuck.
As we determined in ticket ID 300239, the nRF Connect SDK does not support my version 3.0.0 of the PCA10040 DK.
And as we determined in ticket ID 300238...
Im working with this example .
My problem is although I configure the NetworkKey in this file:
When I run the example in my nrf52840DK It always set a random Network...
Hi,
We are evaluating the Tracker V2 application. We enabled AGPS and set "activeWaitTime" to 3600s.
I have some doubts if AGPS is really used, since the terminal...
Our project is running on a nRF9160 using the SDK v2.1.0.
We want to store some data on an external SPI NOR flash installed on the device.
We defined a partition located...
I'm new to nRF9160, Nordic SDK and the build process (for Zephyr, etc.)
I'm new to eSims.
If I solder an eSim chip to the footprint on the nRF9160 DK board, how do I load...
Hi, all
My nRF52840 board is running in the extended advertising mode.
My Android phone can scan it, but my iPhone X can't scan it.
I know that iPhone...
I have installed nRF connect for desktop .In which I am trying to connect nRF 52 DK through programmer software. As soon as I connect the development kit via USB to type B...
I'm trying a project (nrf52) where I use both twi and spi to communicate with a set of sensors (each with a different protocol (twi, spi). after enablling TWI0 and SPI0 I...
Hi,
I've been trying to run the examples of the pc-ble-driver-py library, but I can't get them to run.
Every example gives me the following error: Please specifiy connectivity...
