hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Hi
I do NOT know how to read log messages doing run time, is there a terminal window you Can use. I use Windows and have a nrf52840 and write code in segger embedded st...
Using oneWire library, I was able to get the temperature from the ds18b20. But it didn't work if I put the same code in the Beacon software.
I understand that the softdevice...
I observed that the asset tracker application will not run using code starting with commit a507a3e42229544b195e93a9896ca09c8a4fba85 and newer, on the master branch, in repository...
Hi,
We have been working with a coordinator and a router device based on nRF52840 with nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b
Both devices are Zigbee 3.0 and implement...
I have a binary file for a 3rd party device that the manufacturer has asked me to test on their devices. I have looked through the ZigBee OTA example documentation but it...
Hello:
I am working on a USB bootloader where I have enabled the WDT on entry. After I enable the WDT, the app_timer is set to feed the WDT and to also signal the end of...
Hi
I have a new Thingy:91 that I'm updating.
After I updated the modem software and the firmware with Connect desktop Programmer.
When i could not connect I deleted...
We recently had an issue where a race-condition was caused because we handled entry to sleep mode a bit too carefully. Therefore, I wanted to discuss different methods to...
Hello!
USing help from this forum i have successfullz transmitted adc value from one pin of AIN# to ble and reasing values successfullz but now i am facing an issue that...
Hi Nordic Team：
I use version is: nRF52840 DK Version：nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8\examples\thread\ncp\ftd\uart\hex
Raspberry Pi 3 Version：RaspPi_OT_Border_Router_Demo_v4...
I am new to nrf52.
I want to configure TIMER1 as a counter.
However it does not count. I have added it after advertisement_init
Does the nrf52 have any such limitations...
Hii nordic;
I need to encrypt and decrypt my advertising data i.e;UUID,Major,Minor,etc.; of my nrf52832
So it cannot be seen by third parties
my sdk version is 15...
While trying to communicate through I2C/TWI with a MCP39F521 using a NRF52 DK (NRF52832), the first bit of the received data is always 1. The NRF52 DK is the TWI Master and...
Hi, I'm newbie to nRF DKs but started trying to run examples from pc-ble-driver-py / pc_ble_driver_py / examples / on github in order to get familiar with the nRF52840. I...
Hello
I'm setting up a set of Thingy91 and Thing52 units.
1) I registered 2 thingy91 sim cards and registered the nodes. 2) I see the SIM card in my account on nrfcloud...
