hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
I have application developed that works ok on nRF52 DK (nRF52832) with S112 and now want to migrate it to a custom board with nRF52840.
Could you confirm that S113 is...
Hi:
Since we have a issue that when nRF52840 setting to DCDC mode, our inductive touch will have bigger noise, if setting to LDO mode, the inductive touch noise disappear...
Hi,
I've been trying any way I can think of to work around an issue "51" returned by nrfjprog executed from nrfutil when trying to run serwer from the steps in tutorial...
Hi experts
i am using nRF Sniffer to decrypt the BT Mesh packets with Wireshark, it can work smoothly. However, i tested and found that the packets device key encrypted...
Hello, I am looking at the mesh dfu example code on nRF mesh SDK-4.2.0 on an dk_nrf52840 and I have some questions.
Rather than having both a bootloader and main application...
Hello.
We are developing products using BLE modules.
The one used for that module was "nRF52832 (512kB Flash, 64kB RAM)".
I would like to know
Question 1:
As a...
hi ,
I am working on the nRF52832 , I am trying to store the values in structure and then passing over BLE . I am getting this error after print statement unknown function...
Hi,
I am trying to evaluate nRF5340 FOTA update via Bluetooth. I started with the Bluetooth/peripheral code sample as the basis for my project. I modified the project per...
Could you clarify the use of nrf_esb_set_retransmit_count function?
From what I understood, if it is 0 and it sends a message that wants to be acknowledge , it will not...
To setup the UARTE for use in Zephyr I've configured a nrf52840dk_nrf52840.overlay as Zephyr documentation suggests:
& uart1 {
compatible = "nordic,nrf-uarte"...
Hi, I'm setting up a timer to invoke (via PPI) the ADC in scan mode. It'll read to channels with MAXCNT of 10,000. The ADC built in timer has a value from
[80..2047...
Hi,
I can run the following code within main.c successfully, but it produces the error as shown in the attachment upon execution of k_free(mem.ptr) from with aggregator...
Hello,
in our project we have a nRF52840DK as Central and a custom nRF52832 board as Peripheral. The software on the Central is based on the ble_app_uart_c example and the...
Hi
We are using Nordic NRF52840 in our design. Normally we are using DCDC mode with VDD and VDDH together [Normal mode] connected to 2.2V. In a special case we wanted to...
Hi everyone,
I wanted to make reset pin funtional on nRF52 DK while using pca10040e folder so that I could develop on nRF52810 later, but the reset button did not work as...
