hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
hi i am trying to integrate nrf_butoonless_dfu service in ble_app_uart code in nRF sdk 15.3.0,
i have added the all the required source files and include files and macro...
I am attempting to implement an application using the s140 6.1.0 softdevice on an nRF52840 which "concurrently" advertises as a connectable device while at the same time transmits...
I try to solder a EBYTE NRF52840 module by my PCB and connect with SEGGER programmer. I try to connect to 4 wire VDD, GND, SWDIO, SWCLK, like the one that I have with NRF52832...
I'm migrating a project from SDK 14.2.0 to SDK 15.3.0. I use gcc. I just got it to link and flash and I'm seeing RTT logging OK, to a point. I also have the flashlog in use...
in my application use nrf52 connect with max6675 thermo couple for read temperature
max6675 is configurable in spi mode.
in main.c
in 'nrf_drv_spi_init' not...
Hello,
I use the LAIRD module BL652 with an nRF52832.
My project used the RTC as date/hour counter. I used this RTC to increment a counter each 125 ms of RTC interrupt...
Hi,
I am using s132 6.1.1 with SDK 15.2, developing with keil , my code works completely fine on Development Kit but it doesn't boot up on our custom board which doesn't...
Hello all,
I updated modem firmware mfw_nrf9160_0.7.0-15.alpha.zip. I have iBASIS SIM card in modem and started with at_client example and country also has nb-iot support...
Hi,
I need my NRF9160 to do some task multiple times a day.
i.e.
in 8:25, 9:40,12:30,...
each day.
would it be considered good practice to use kernel timers to for...
I followed the tutorial here:
https://devzone.nordicsemi.com/tutorials/b/getting-started/posts/getting-started-with-nrf9160-dk?CommentId=98ebb127-8333-4fca-8409-53845d1e1401...
I am trying to port existing software to a custom nrf9160 board. I am using latest nrf connect sdk updated with git and west. Could somebody from Nordic comment about the...
I tried to increase the bootloader size by reducing IROM start address and increasing size but I always get the same error:
.\_build\nrf52832_xxaa_s132.axf: Error: L6407E...
I would like to perform FDS garbage collection only when it is close to being full. I can read the fds_stat to see the number of words used and the words freeable but what...
Hi all,
I would like to get the complete name from the connected peripheral by reading the device name characteristic (0x2A00) in the Generic Access Service (0x1800). I...
I want to use sys_time_get() on my ble app in SES env. but it looks like sdk 14.2.0 doesn't support sys_time_get() on SES env. So I'd like to use the similar function such...
